verified AirTAC China Authorized Export Seller shield 100% Genuine AirTAC Parts workspace_premium 1-Year Warranty
appsShop by Modelexpand_more
person shopping_cart Request a QuoteQuote
AirTAC SE Series · ISO 15552 Cylinder

Airtac SE50 Standard Cylinder SE50X200SH

The AirTAC SE50 Standard Cylinder SE50X200SH is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø50mm bore and 200mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.

  • BoreØ50 mm
  • Stroke200 mm
  • Port sizePT1/4
  • Acting typeDouble acting
  • Rod threadM16×1.5
  • CushionAdjustable, 30 mm
$96.53 $104.03Save 7% Standard model — usually dispatched in 3-5 days
Request a Quote
  • No minimum order. A single piece can be ordered.
  • Shipped from our own warehouse: most standard models dispatch in 3–5 days; custom and non-standard models take 8–10 business days. Transit time after that depends on the destination.
Compare every SE50 stroke, mounting and version on one page All SE50 codes →
verified Genuine AirTAC workspace_premium 1-year warranty bolt Reply in 7 h

About the Airtac SE50 Standard Cylinder SE50X200SH

The AirTAC SE50X200SH is a double-acting single-rod ISO 15552 profile cylinder engineered for rigorous thermal and dynamic cycles. It produces a substantial 982 N of push force at 0.5 MPa and 1374 N at 0.7 MPa across its 200 mm stroke. The square extruded aluminum barrel omits external tie rods, yielding a compact, corrosion-resistant body that mounts flush against machine frames while protecting internal mechanics.

Equipped with a high-temperature Viton (FKM) seal, this unit reliably operates in environments up to 150 C. The integrated magnet (-S) directly supports AirTAC CMSE reed and DMSE electronic sensors for precise end-of-stroke detection. Furthermore, field-adjustable pneumatic cushioning at both ends allows mechanics to tune the deceleration profile, softening hard end stops during high-velocity 30-800 mm/s cycles.

Airtac SE50 Standard Cylinder SE50X200SH Technical Specifications

ModelAirtac SE50 Standard Cylinder SE50X200SH
SeriesSE ISO 15552 profile cylinder
Bore sizeØ50 mm
Stroke200 mm
Acting typeDouble acting
Port sizePT1/4
Rod threadM16×1.5
FluidAir (filtered by 40µm element)
Operating pressure0.15 – 1.0 MPa
Proof pressure1.5 MPa
Temperature-20 to +70 °C (0–150 °C with FKM seals)
Speed range30 – 800 mm/s
CushionAdjustable, 30 mm
Max strokeUp to 1200 mm

Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).

Theoretical Output Force (Ø50mm)

PressurePush forcePull force
0.5 MPa982 N825 N
0.7 MPa1374 N—
Max (@1.0 MPa)200 kgf

Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.

Model Code: Airtac SE50 Standard Cylinder SE50X200SH

SEISO 15552 / VDMA 24562 profile-barrel double-acting cylinder.
50Bore size in mm.
×200Stroke length in mm.
-SOptional built-in magnet for CMSE / DMSE sensor sensing.

Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).

Where the Airtac SE50 Standard Cylinder SE50X200SH Is Used

package_2

Shrink Wrap Tunnels

Handles carton transitions through high-heat sealing zones, utilizing the Viton seal to withstand 150 C ambient temperatures while providing 982 N of push force.

factory

Plastic Injection Mold Ejection

Drives mold ejection plates with 1374 N of thrust at 0.7 MPa, relying on the integrated magnet for DMSE electronic timing and adjustable cushions to protect sensitive tooling.

science

Lab Dryer Doors

Actuates heavy thermal chamber doors, where the tie-rod-free extruded profile ensures flush mounting and the FKM seal resists degradation under sustained heat.

Is the Airtac SE50 Standard Cylinder SE50X200SH the Right Cylinder?

When sizing this actuator, compare its 982 N push at 0.5 MPa against adjacent bores: stepping down to a 40 mm bore yields 628 N, while stepping up to a 63 mm bore provides 1559 N. Because the SE50X200SH is dimensionally interchangeable per ISO 15552, it serves as a direct replacement for other ISO 15552 cylinders, sharing standard mounting hardware and port PT1/4 connections. For 200 mm strokes, side-loading is moderate, but ensure the M16x1.5 rod thread and bearing are not subjected to excessive lateral stress; an external guide is recommended for heavy off-center loads. Note that this cylinder cannot hold a load if air pressure is lost; apply a BSE rod lock for position-holding safety.

AirtacDistr lists every SE50 order code with its price on one page at https://airtacdistr.com/products/airtac-se50-iso-air-cylinder

Quick checklist

  • ✓ Required force at your working pressure
  • ✓ Stroke and mounting space
  • ✓ Port/thread type (PT/G)
  • ✓ Magnet (-S) for CMSE/DMSE sensors?
  • ✓ Side load — consider a guided cylinder
Ask an Engineer

Installation & Maintenance Notes

  • check Use clean air filtered to 40µm or finer.
  • check Keep within 0.15 – 1.0 MPa operating pressure.
  • check Avoid side load on the piston rod.
  • check Adjust end cushion screws for smooth stops.
  • check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
  • check Installation by qualified personnel per AirTAC docs.

Airtac SE50 Standard Cylinder SE50X200SH FAQ

The SE50X200SH generates 982 N push and 825 N pull at 0.5 MPa, 1374 N push at 0.7 MPa, and a maximum push of 200 kgf at 1.0 MPa. It features a PT1/4 port and a 20 mm rod.

No, the adjustable air cushion only decelerates the piston near the stroke end and does not lock the position. If the application requires holding a load without live air pressure, you must use a BSE series rod lock or an external pilot-operated check valve.

verified

Authorized Export Seller

Genuine AirTAC parts produced by AirTAC factory.

workspace_premium

1-Year Warranty

Covers non-human-caused product damage.

local_shipping

Fast Dispatch

Most standard models are dispatched in 3-5 days.

bolt

Fast Reply

Most inquiries answered within 7 hours.

Related AirTAC SE Cylinders

Request a Quote for Airtac SE50 Standard Cylinder SE50X200SH

Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.

Thank you. We received your request for SE50X200SH and will confirm price, availability and lead time — usually within 7 hours.

For the fastest response, keep the complete model number above and include a clear photo of the product label. If photo upload is unavailable, email photos to [email protected] with your model number.