
The AirTAC SE50 Standard Cylinder SE50X222S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø50mm bore and 222mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE50X222S is a double-acting single-rod profile cylinder operating on the ISO 15552 interface, delivering a robust 982 N push at 0.5 MPa. Its 222 mm stroke is a non-standard made-to-order length, tailored precisely for specialized machine spacing requirements without compromising the standardized 50 mm bore footprint.
Built with an extruded aluminum barrel free of external tie rods, the body is compact and highly resistant to corrosion. The integrated -S magnet enables direct position tracking via CMSE reed or DMSE electronic sensors, while the field-adjustable air cushioning at both ends allows technicians to fine-tune end-of-stroke deceleration for moving loads.
| Model | Airtac SE50 Standard Cylinder SE50X222S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø50 mm |
| Stroke | 222 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 982 N | 825 N |
| 0.7 MPa | 1374 N | — |
| Max (@1.0 MPa) | 200 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 50 | Bore size in mm. |
| ×222 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Provides the precise 982 N push and 222 mm extension needed to fold large corrugated carton flaps on high-speed packaging lines without crushing the board.
Actuates a routing gate on a conveyor network, using its custom 222 mm stroke to clear wider pallets while the DMSE electronic sensor confirms gate position.
Shifts a heavy sliding CNC machine tool door open and closed, utilizing the adjustable end cushions to soften the hard stops at rapid transit speeds.
When sizing this actuator, you can step down to the 40 mm bore for a lighter 628 N push at 0.5 MPa, or step up to the 63 mm bore if your application requires a heavier 1559 N thrust. Because the 222 mm stroke exceeds the standard list, expect a brief made-to-order lead time. As a true ISO 15552 profile cylinder, it serves as a direct dimensional replacement for any standard 50 mm bore, 222 mm stroke unit, utilizing standard PT1/4 ports and shared mounting accessories.
Since the stroke is over 200 mm, the 20 mm rod and its bearing face increased bending moments under lateral stress; an external guide rail should be installed to prevent side-load wear. Note that the adjustable pneumatic cushion only decelerates the piston near stroke end and does not lock the load—if air pressure is lost, the rod will drift, requiring a BSE rod lock for secure holding.
AirtacDistr lists every SE50 order code with its price on one page at https://airtacdistr.com/products/airtac-se50-iso-air-cylinder
Quick checklist
At 0.5 MPa, the push force is 982 N and the pull force is 825 N. At 0.7 MPa, the push force increases to 1374 N. The maximum push force is 200 kgf when operated at the 1.0 MPa pressure limit.
Yes, the SE50X222S is dimensionally interchangeable per ISO 15552. You can drop it into existing 50 mm bore mounting hardware using the standard PT1/4 ports, though the 222 mm stroke is a non-standard made-to-order length.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.