
The AirTAC SE50 Standard Cylinder SE50X225 is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø50mm bore and 225mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE50X225 is a double-acting single-rod ISO 15552 profile cylinder engineered to deliver 982 N of push force at 0.5 MPa over a 225 mm stroke. Because this length falls outside the standard stroke list, it is supplied as a non-standard made-to-order configuration, ensuring you get the exact travel required for your machine without compromising on the ISO 15552 mounting interface.
Built with a square extruded aluminum barrel that omits external tie rods, the body is highly compact and corrosion-resistant, allowing it to mount flush in tight spaces. The end caps feature field-adjustable pneumatic cushioning at both ends, letting technicians dial in the deceleration via a set screw to soften hard end stops at high cycle speeds. Note that this specific SKU lacks the -S magnet option, so it does not support CMSE or DMSE position sensing without modification.
| Model | Airtac SE50 Standard Cylinder SE50X225 |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø50 mm |
| Stroke | 225 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 982 N | 825 N |
| 0.7 MPa | 1374 N | — |
| Max (@1.0 MPa) | 200 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 50 | Bore size in mm. |
| ×225 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Uses the 225 mm stroke to push medium-weight parcels off a main sorting belt, relying on the 982 N push force at 0.5 MPa to handle cardboard boxes without bouncing back.
Actuates a film carriage clamp on a stretch wrapper, utilizing the compact tie-rod-free profile to fit within the narrow machinery frame while maintaining consistent pressure.
Operates a cutoff press gate for aluminum profiles, where the field-adjustable cushioning absorbs the kinetic energy of the 50 mm bore at high speeds to prevent end-cap damage.
When sizing this actuator, compare its 982 N push @0.5 MPa against its neighbors: stepping down to a 40 mm bore yields 628 N, while stepping up to a 63 mm bore provides 1559 N. This 50 mm bore hits a reliable middle ground for medium-duty loads. Because the 225 mm stroke exceeds standard lengths, it is flagged as non-standard_stroke. Furthermore, at this travel distance, the unsupported rod is susceptible to bending under lateral loads; always pair it with an external guide rail to prevent premature rod-bearing wear. Remember that the adjustable air cushion only decelerates the piston near the end of travel—it is not a locking device. If your fixture must hold a vertical load without live air pressure, integrate an external BSE rod lock or a pilot-operated check valve.
AirtacDistr lists every SE50 order code with its price on one page at https://airtacdistr.com/products/airtac-se50-iso-air-cylinder
Quick checklist
At 0.5 MPa, this 50 mm bore cylinder provides 982 N of push force and 825 N of pull force. At 0.7 MPa, the push force increases to 1374 N. The maximum push capacity is 200 kgf at 1.0 MPa. It operates at a speed range of 30-800 mm/s.
Yes, the SE50X225 is dimensionally interchangeable per ISO 15552 / VDMA 24562 standards. You can use it as a direct replacement for other ISO 15552 profile cylinders with a 50 mm bore and 225 mm stroke, utilizing standard mounting accessories and the PT1/4 port.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.