
The AirTAC SE50 Standard Cylinder SE50X225S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø50mm bore and 225mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE50X225S is a double-acting single-rod profile cylinder built to ISO 15552 dimensions, delivering a push force of 982 N at 0.5 MPa. Its square extruded aluminum barrel eliminates external tie rods, yielding a compact footprint that mounts flush against machine frames while resisting corrosion. The included -S magnet enables direct position feedback using AirTAC CMSE reed or DMSE electronic sensors.
Field-adjustable pneumatic cushioning at both stroke ends allows technicians to tune the exhaust bleed and soften hard end-stops, protecting payloads during high-speed actuation. Because the 225 mm stroke exceeds the standard 120 mm catalog maximum for this bore, it is produced as a non-standard made-to-order unit.
| Model | Airtac SE50 Standard Cylinder SE50X225S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø50 mm |
| Stroke | 225 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 982 N | 825 N |
| 0.7 MPa | 1374 N | — |
| Max (@1.0 MPa) | 200 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 50 | Bore size in mm. |
| ×225 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Applies 982 N of push force at 0.5 MPa to cleanly fold heavy cardboard flaps on high-speed packaging lines before tape sealing.
Uses the 225 mm stroke to push finished pallets off a main conveyor onto a secondary wrapping lane, tracking position via the -S magnet and DMSE sensor.
Secures aluminum extrusion blanks inside a machining center, relying on the field-adjustable cushion to prevent jarring impacts at the end of the 225 mm travel.
Selecting this 50 mm bore makes sense when you need 982 N of push force at 0.5 MPa. If your payload is lighter, stepping down to the 40 mm bore drops the output to 628 N, while moving up to the 63 mm bore increases it to 1559 N. As a dimensionally interchangeable ISO 15552 cylinder, it serves as a direct replacement for other ISO 15552 profile cylinders, matching the PT1/4 port, M16x1.5 rod thread, and standard mounting accessories.
Because the 225 mm stroke is non-standard and exceeds 300 mm is not applicable here, but at this length you must still evaluate rod bearing loads. An unsupported 225 mm extension can induce side-load bending; always use an external guide rail to prevent premature seal wear. Remember that an unpowered SE cylinder drifts under load—the adjustable cushion only decelerates the piston near stroke end and will not hold position if air pressure is lost.
AirtacDistr lists every SE50 order code with its price on one page at https://airtacdistr.com/products/airtac-se50-iso-air-cylinder
Quick checklist
At 0.5 MPa, the push force is 982 N and the pull force is 825 N. At 0.7 MPa, the push force increases to 1374 N. The maximum push force is 200 kgf at 1.0 MPa, and the operational speed range is 30-800 mm/s.
Yes, the SE50X225S is dimensionally interchangeable per ISO 15552. You can drop it into existing mounting hardware matching the 50 mm bore footprint, PT1/4 ports, and M16x1.5 rod thread without machining new brackets.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.