verified AirTAC China Authorized Export Seller shield 100% Genuine AirTAC Parts workspace_premium 1-Year Warranty
appsShop by Modelexpand_more
person shopping_cart Request a QuoteQuote
AirTAC SE Series · ISO 15552 Cylinder

Airtac SE50 Standard Cylinder SE50X230S

The AirTAC SE50 Standard Cylinder SE50X230S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø50mm bore and 230mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.

  • BoreØ50 mm
  • Stroke230 mm
  • Port sizePT1/4
  • Acting typeDouble acting
  • Rod threadM16×1.5
  • CushionAdjustable, 30 mm
$92.09 $99.59Save 7% Standard model — usually dispatched in 3-5 days
Request a Quote
  • No minimum order. A single piece can be ordered.
  • Shipped from our own warehouse: most standard models dispatch in 3–5 days; custom and non-standard models take 8–10 business days. Transit time after that depends on the destination.
Compare every SE50 stroke, mounting and version on one page All SE50 codes →
verified Genuine AirTAC workspace_premium 1-year warranty bolt Reply in 7 h

About the Airtac SE50 Standard Cylinder SE50X230S

The AirTAC SE50X230S is a double-acting single-rod profile cylinder built to the ISO 15552 standard, delivering a robust 982 N push force at 0.5 MPa. Its square extruded aluminum barrel eliminates external tie rods, yielding a compact, corrosion-resistant body that mounts flush against machine frames. This clean profile simplifies retrofitting into tight spaces without protruding hardware.

Equipped with a built-in magnet (-S), this unit supports AirTAC CMSE reed and DMSE electronic position sensors along the three integrated side grooves. The field-adjustable pneumatic cushioning at both ends allows technicians to tune end-of-stroke deceleration via a set screw, softening hard impacts during high-speed 30-800 mm/s cycling.

Airtac SE50 Standard Cylinder SE50X230S Technical Specifications

ModelAirtac SE50 Standard Cylinder SE50X230S
SeriesSE ISO 15552 profile cylinder
Bore sizeØ50 mm
Stroke230 mm
Acting typeDouble acting
Port sizePT1/4
Rod threadM16×1.5
FluidAir (filtered by 40µm element)
Operating pressure0.15 – 1.0 MPa
Proof pressure1.5 MPa
Temperature-20 to +70 °C (0–150 °C with FKM seals)
Speed range30 – 800 mm/s
CushionAdjustable, 30 mm
Max strokeUp to 1200 mm

Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).

Theoretical Output Force (Ø50mm)

PressurePush forcePull force
0.5 MPa982 N825 N
0.7 MPa1374 N—
Max (@1.0 MPa)200 kgf

Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.

Model Code: Airtac SE50 Standard Cylinder SE50X230S

SEISO 15552 / VDMA 24562 profile-barrel double-acting cylinder.
50Bore size in mm.
×230Stroke length in mm.
-SOptional built-in magnet for CMSE / DMSE sensor sensing.

Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).

Where the Airtac SE50 Standard Cylinder SE50X230S Is Used

package_2

Carton Flap Folding

Drives the mechanical arms that fold top flaps on high-speed corrugated box erectors, utilizing the 230 mm stroke and 982 N push to cleanly clear the packaging path.

conveyor_belt

Pallet Diverter Gate

Actuates routing gates on modular conveyor lines, relying on the magnetic piston and DMSE sensors to confirm gate position before heavy pallets transition lanes.

science

Lab Sample Indexing

Pushes sample trays into analytical instruments, where the adjustable end cushions soften the 230 mm extension to prevent liquid spillage in delicate test tubes.

Is the Airtac SE50 Standard Cylinder SE50X230S the Right Cylinder?

Selecting the SE50X230S gives you 982 N of thrust at 0.5 MPa. If your payload is lighter, stepping down to the 40 mm bore drops the push to 628 N, while moving up to the 63 mm bore increases it to 1559 N. Because this is a 230 mm stroke, the unsupported piston rod is prone to bending under lateral loads; always pair it with an external guide rail to prevent rod-bearing wear. As a standard ISO 15552 profile cylinder, it serves as a direct replacement for any equivalent 50 mm bore, 230 mm stroke unit with a PT1/4 port and basic mounting.

Note that the adjustable air cushion only decelerates the piston near the stroke ends; it is not a locking device. If air pressure drops or the valve centers, the cylinder will drift and cannot hold a vertical load. For suspended loads requiring fail-safe holding, consider the BSE rod-lock variant or an external pilot-operated check valve.

AirtacDistr lists every SE50 order code with its price on one page at https://airtacdistr.com/products/airtac-se50-iso-air-cylinder

Quick checklist

  • ✓ Required force at your working pressure
  • ✓ Stroke and mounting space
  • ✓ Port/thread type (PT/G)
  • ✓ Magnet (-S) for CMSE/DMSE sensors?
  • ✓ Side load — consider a guided cylinder
Ask an Engineer

Installation & Maintenance Notes

  • check Use clean air filtered to 40µm or finer.
  • check Keep within 0.15 – 1.0 MPa operating pressure.
  • check Avoid side load on the piston rod.
  • check Adjust end cushion screws for smooth stops.
  • check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
  • check Installation by qualified personnel per AirTAC docs.

Airtac SE50 Standard Cylinder SE50X230S FAQ

At 0.5 MPa, this 50 mm bore cylinder provides 982 N of push force and 825 N of pull force. At 0.7 MPa, the push force reaches 1374 N, with a maximum push capacity of 200 kgf at 1.0 MPa. The operational speed range is 30-800 mm/s.

Yes, the SE50X230S is dimensionally interchangeable per ISO 15552. You can drop it into existing mounts designed for other standard 50 mm profile cylinders. It uses a PT1/4 port and a standard M16x1.5 rod thread, and the built-in magnet works directly with AirTAC CMSE and DMSE sensors.

verified

Authorized Export Seller

Genuine AirTAC parts produced by AirTAC factory.

workspace_premium

1-Year Warranty

Covers non-human-caused product damage.

local_shipping

Fast Dispatch

Most standard models are dispatched in 3-5 days.

bolt

Fast Reply

Most inquiries answered within 7 hours.

Related AirTAC SE Cylinders

Request a Quote for Airtac SE50 Standard Cylinder SE50X230S

Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.

Thank you. We received your request for SE50X230S and will confirm price, availability and lead time — usually within 7 hours.

For the fastest response, keep the complete model number above and include a clear photo of the product label. If photo upload is unavailable, email photos to [email protected] with your model number.