
The AirTAC SE50 Standard Cylinder SE50X250H is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø50mm bore and 250mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE50X250H is a double-acting, single-rod ISO 15552 profile cylinder engineered for rigorous thermal environments. Equipped with high-temperature FKM (Viton) seals, it operates reliably from -20 to +150 C, extending its usability into hot molding and drying processes where standard elastomers fail. It yields a robust 982 N push and 825 N pull force at 0.5 MPa, driven through a PT1/4 port.
This unit features a square extruded aluminum barrel that entirely eliminates external tie rods, yielding a smooth, corrosion-resistant exterior that mounts flush against machine frames. The integrated sensor grooves on three sides remain available for future automation upgrades, though this specific SKU ships without a position-sensing magnet. Field-adjustable pneumatic cushioning at both stroke ends allows technicians to dial in deceleration, softening hard mechanical impacts at high cycle rates.
| Model | Airtac SE50 Standard Cylinder SE50X250H |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø50 mm |
| Stroke | 250 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 982 N | 825 N |
| 0.7 MPa | 1374 N | — |
| Max (@1.0 MPa) | 200 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 50 | Bore size in mm. |
| ×250 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Clamps heated plastic sheets in a 150 C thermoforming oven using 982 N of thrust at 0.5 MPa, relying on the FKM Viton seals to survive continuous radiant heat without degrading.
Actuates a 250 mm stroke routing gate to deflect newly formed glass bottles on a cooling conveyor, where the adjustable air cushion absorbs the kinetic energy of rapid 30-800 mm/s cycles.
Holds corrugated cartons stationary beneath a shrink-wrap heat tunnel, utilizing the tie-rod-free extruded aluminum body to mount seamlessly within the compact machinery frame.
Selecting the SE50X250H is optimal when your process demands 982 N of push force at 0.5 MPa alongside resistance to 150 C heat. If you need to scale down, the 40 mm bore variant provides 628 N of push at 0.5 MPa; stepping up to the 63 mm bore yields 1559 N. Because this is a standard 250 mm stroke exceeding the 300 mm threshold, the 20 mm piston rod and rod-bearing interface experience greater bending moments under side loads—always incorporate an external guide rail to prevent premature seal wear.
As a true ISO 15552 profile cylinder, this 50 mm bore, 250 mm stroke unit with a PT1/4 port serves as a direct dimensional replacement for other ISO 15552 cylinders, sharing identical mounting footprints (LB, FA, TC, etc.). Note that a plain SE cylinder decelerates via its adjustable end cushions but cannot hold a load if air pressure is lost; if your fixture requires static positioning during an exhaust or power failure, integrate an external pilot-operated check valve or specify a BSE rod-lock variant.
AirtacDistr lists every SE50 order code with its price on one page at https://airtacdistr.com/products/airtac-se50-iso-air-cylinder
Quick checklist
The 50 mm bore generates a push force of 982 N and a pull force of 825 N at 0.5 MPa. At 0.7 MPa, the push force is 1374 N, with a maximum push capacity of 200 kgf at 1.0 MPa. Because this model uses H-code FKM (Viton) seals, its operating temperature spans -20 to +150 C.
Yes, it is dimensionally interchangeable with any standard ISO 15552 cylinder, matching bore, stroke, and PT1/4 port dimensions for a direct retrofit. However, while its adjustable air cushions decelerate the piston at stroke ends, it cannot hold a vertical load if air pressure drops; for position holding, you need a BSE rod-lock cylinder or external check valve.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.