
The AirTAC SE50 Standard Cylinder SE50X250S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø50mm bore and 250mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE50X250S is a double-acting, single-rod ISO 15552 profile cylinder engineered to deliver 982 N of push force at 0.5 MPa. Its square extruded aluminum barrel eliminates external tie rods, yielding a compact footprint that mounts flush and resists corrosion in demanding environments.
Equipped with a built-in magnet (-S), this unit seamlessly integrates with AirTAC CMSE reed and DMSE electronic sensors for precise end-position detection. The field-adjustable air cushioning at both ends allows technicians to tune end-of-stroke deceleration, softening hard impacts when cycling at speeds up to 800 mm/s.
| Model | Airtac SE50 Standard Cylinder SE50X250S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø50 mm |
| Stroke | 250 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 982 N | 825 N |
| 0.7 MPa | 1374 N | — |
| Max (@1.0 MPa) | 200 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 50 | Bore size in mm. |
| ×250 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Provides the precise 982 N push and 250 mm travel needed to fold and seal corrugated packaging flaps on high-speed filling lines.
Actuates routing gates to redirect heavy pallets along roller conveyors, utilizing the full 250 mm stroke to clear the transport path.
Extends to shuttle tool holders into machining centers, relying on the -S magnet and DMSE sensors to confirm safe tool handoff.
Delivering 982 N push at 0.5 MPa, this 50 mm bore is the ideal middle ground. If your application requires less force and a smaller footprint, the 40 mm bore provides 628 N; if you need heavier thrust, stepping up to the 63 mm bore yields 1559 N. Because the 250 mm stroke is substantial, an external guide is recommended to prevent rod-bearing bending under high side loads.
As a true ISO 15552 profile cylinder, it serves as a direct replacement for any standard 50 mm bore, 250 mm stroke cylinder with a PT1/4 port and matching mounting accessories. Note that the adjustable air cushion only decelerates the piston near stroke end; it is not a locking device. If the machine must hold a load vertically without live air pressure, you must use a BSE rod lock or external pilot check valve.
AirtacDistr lists every SE50 order code with its price on one page at https://airtacdistr.com/products/airtac-se50-iso-air-cylinder
Quick checklist
At 0.5 MPa, this 50 mm bore cylinder outputs 982 N of push force and 825 N of pull force. At 0.7 MPa, the push force increases to 1374 N, with a maximum push capacity of 200 kgf at 1.0 MPa. The standard operating speed ranges from 30 to 800 mm/s.
Yes. The SE50X250S is dimensionally interchangeable per ISO 15552 standards. You can drop it directly into existing setups using standard 50 mm mounting accessories, provided your system utilizes the default PT1/4 port thread.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.