verified AirTAC China Authorized Export Seller shield 100% Genuine AirTAC Parts workspace_premium 1-Year Warranty
appsShop by Modelexpand_more
person shopping_cart Request a QuoteQuote
AirTAC SE Series · ISO 15552 Cylinder

Airtac SE50 Standard Cylinder SE50X250SFTC

The AirTAC SE50 Standard Cylinder SE50X250SFTC is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø50mm bore and 250mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.

  • BoreØ50 mm
  • Stroke250 mm
  • Port sizePT1/4
  • Acting typeDouble acting
  • Rod threadM16×1.5
  • CushionAdjustable, 30 mm
$113.03 $120.53Save 6% Standard model — usually dispatched in 3-5 days
Request a Quote
  • No minimum order. A single piece can be ordered.
  • Shipped from our own warehouse: most standard models dispatch in 3–5 days; custom and non-standard models take 8–10 business days. Transit time after that depends on the destination.
Compare every SE50 stroke, mounting and version on one page All SE50 codes →
verified Genuine AirTAC workspace_premium 1-year warranty bolt Reply in 7 h

About the Airtac SE50 Standard Cylinder SE50X250SFTC

The AirTAC SE50X250S is a double-acting single-rod ISO 15552 profile cylinder engineered for 982 N push force at 0.5 MPa. Its square extruded aluminum barrel omits external tie rods, yielding a flush mounting surface that resists corrosion and simplifies fitting in tight machinery frames. The integrated -S magnet enables direct position tracking via CMSE reed or DMSE electronic sensors.

Field-adjustable pneumatic cushioning at both stroke ends allows technicians to tune end-of-travel deceleration via a set screw, softening hard impacts when cycling at speeds up to 800 mm/s. This FTC center-trunnion variant provides a robust pivoting anchor point for angular load actuation across a 250 mm stroke.

Airtac SE50 Standard Cylinder SE50X250SFTC Technical Specifications

ModelAirtac SE50 Standard Cylinder SE50X250SFTC
SeriesSE ISO 15552 profile cylinder
Bore sizeØ50 mm
Stroke250 mm
Acting typeDouble acting
Port sizePT1/4
Rod threadM16×1.5
FluidAir (filtered by 40µm element)
Operating pressure0.15 – 1.0 MPa
Proof pressure1.5 MPa
Temperature-20 to +70 °C (0–150 °C with FKM seals)
Speed range30 – 800 mm/s
CushionAdjustable, 30 mm
Max strokeUp to 1200 mm

Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).

Theoretical Output Force (Ø50mm)

PressurePush forcePull force
0.5 MPa982 N825 N
0.7 MPa1374 N—
Max (@1.0 MPa)200 kgf

Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.

Model Code: Airtac SE50 Standard Cylinder SE50X250SFTC

SEISO 15552 / VDMA 24562 profile-barrel double-acting cylinder.
50Bore size in mm.
×250Stroke length in mm.
-SOptional built-in magnet for CMSE / DMSE sensor sensing.

Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).

Where the Airtac SE50 Standard Cylinder SE50X250SFTC Is Used

package_2

Case Erector Flap Folding

Applies 982 N of push force to reliably fold heavy cardboard carton flaps during continuous high-speed packaging line cycles over the 250 mm travel.

conveyor_belt

Pallet Diverter Gate

Utilizes the FTC center trunnion to smoothly pivot a routing gate, guiding heavy wooden pallets onto secondary conveyor tracks without binding.

precision_manufacturing

CNC Lathe Bar Feed Pusher

Leverages the 250 mm stroke and built-in magnet to drive raw steel stock into the collet, triggering a DMSE sensor to confirm material seating.

Is the Airtac SE50 Standard Cylinder SE50X250SFTC the Right Cylinder?

Delivering 982 N push at 0.5 MPa, this 50 mm bore is a strong middle ground. If your load is lighter, stepping down to the 40 mm bore yields 628 N of push force, saving valuable space and air consumption. Conversely, heavier dynamics may require stepping up to the 63 mm bore, which provides 1559 N of thrust. Since the 250 mm stroke exceeds the 300 mm threshold, the unsupported rod is prone to bending under lateral stress; always incorporate an external guide rail to prevent premature rod-bearing wear.

As a dimensionally interchangeable ISO 15552 component, it serves as a direct replacement for competing profile cylinders. Specify the PT1/4 port, FTC trunnion mount, and -S magnet requirement when ordering. Remember that the air cushion only decelerates the piston near stroke end and will not hold a load if air pressure drops; for dead-load holding, utilize a BSE rod lock.

AirtacDistr lists every SE50 order code with its price on one page at https://airtacdistr.com/products/airtac-se50-iso-air-cylinder

Quick checklist

  • ✓ Required force at your working pressure
  • ✓ Stroke and mounting space
  • ✓ Port/thread type (PT/G)
  • ✓ Magnet (-S) for CMSE/DMSE sensors?
  • ✓ Side load — consider a guided cylinder
Ask an Engineer

Installation & Maintenance Notes

  • check Use clean air filtered to 40µm or finer.
  • check Keep within 0.15 – 1.0 MPa operating pressure.
  • check Avoid side load on the piston rod.
  • check Adjust end cushion screws for smooth stops.
  • check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
  • check Installation by qualified personnel per AirTAC docs.

Airtac SE50 Standard Cylinder SE50X250SFTC FAQ

At 0.5 MPa, this 50 mm bore cylinder provides 982 N of push force and 825 N of pull force. At 0.7 MPa, the push force increases to 1374 N, with a maximum push capacity of 200 kgf at 1.0 MPa. The operational speed range is 30-800 mm/s.

Yes, the SE50X250S is a true ISO 15552 profile cylinder, making its mounting dimensions fully interchangeable with other ISO 15552 standard profile cylinders. The -S magnet is fully compatible with AirTAC CMSE reed and DMSE electronic sensors.

verified

Authorized Export Seller

Genuine AirTAC parts produced by AirTAC factory.

workspace_premium

1-Year Warranty

Covers non-human-caused product damage.

local_shipping

Fast Dispatch

Most standard models are dispatched in 3-5 days.

bolt

Fast Reply

Most inquiries answered within 7 hours.

Related AirTAC SE Cylinders

Request a Quote for Airtac SE50 Standard Cylinder SE50X250SFTC

Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.

Thank you. We received your request for SE50X250SFTC and will confirm price, availability and lead time — usually within 7 hours.

For the fastest response, keep the complete model number above and include a clear photo of the product label. If photo upload is unavailable, email photos to [email protected] with your model number.