
The AirTAC SE50 Standard Cylinder SE50X262SN is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø50mm bore and 262mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE50X262SN is a double-acting, single-rod ISO 15552 profile cylinder with a 50 mm bore and a 262 mm stroke. It delivers a push force of 982 N and a pull force of 825 N at 0.5 MPa, making it a solid choice for mid-range actuation. The extruded aluminum barrel lacks external tie rods, yielding a clean, corrosion-resistant profile that mounts flush against frames.
This specific unit features an NBR seal and a built-in magnet for position sensing. The magnet interfaces directly with AirTAC CMSE reed and DMSE electronic sensors, which drop into the sensor grooves on three sides of the body. Furthermore, both end caps carry field-adjustable pneumatic cushioning, allowing you to tune out hard end stops during high-speed cycling.
| Model | Airtac SE50 Standard Cylinder SE50X262SN |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø50 mm |
| Stroke | 262 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 982 N | 825 N |
| 0.7 MPa | 1374 N | — |
| Max (@1.0 MPa) | 200 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 50 | Bore size in mm. |
| ×262 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Uses the 982 N push force to swing heavy cardboard cartons between sorting lanes on a high-speed logistics conveyor.
Actuates a metal chip discharge flap, relying on the NBR seal and adjustable cushioning to withstand repetitive impact in a machining cell.
Extends 262 mm to position a stretch film roll carriage, using the built-in magnet and DMSE sensors to confirm film delivery depth.
With a 0.5 MPa push of 982 N, this 50 mm bore sits comfortably between the 40 mm (628 N) and 63 mm (1559 N) models. Step down to the 40 mm if your payload is lighter, or move up to the 63 mm if you need significantly more thrust. Because this is a 262 mm stroke (a non-standard length beyond the 250 mm standard mark), expect a made-to-order lead time. For an unsupported 262 mm extension, the Ø20 mm rod and M16x1.5 thread carry moderate side-load capacity, but an external guide is recommended to prevent rod-bearing bending. As a double-acting ISO 15552 cylinder, it provides a direct dimensional replacement for other ISO 15552 profile cylinders, sharing standard mounting hardware like FA or LB brackets. Note that the adjustable air cushion only decelerates the piston near stroke end; it does not hold a load. If air is lost, the piston drifts, so use a BSE rod lock for position holding.
AirtacDistr lists every SE50 order code with its price on one page at https://airtacdistr.com/products/airtac-se50-iso-air-cylinder
Quick checklist
At 0.5 MPa, the push force is 982 N and the pull force is 825 N. At 0.7 MPa, the push force is 1374 N. The maximum push force is 200 kgf at 1.0 MPa. The operational speed range is 30-800 mm/s.
Yes, the SE50X262SN is dimensionally interchangeable per ISO 15552 / VDMA 24562 standards. It shares the same 50 mm bore, 262 mm stroke, PT1/4 port, and mounting footprint, allowing a direct replacement using your existing brackets.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.