
The AirTAC SE50 Standard Cylinder SE50X290S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø50mm bore and 290mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE50X290S is a double-acting, single-rod ISO 15552 profile cylinder engineered to deliver 982 N of push force and 825 N of pull force at 0.5 MPa. Driven by filtered air over a 30-800 mm/s speed range, it integrates a 50 mm bore with a 290 mm stroke, making it a robust choice for mid-range linear actuation.
Because this configuration includes the -S magnet code, the piston is fully compatible with AirTAC CMSE reed and DMSE electronic sensors for precise end-position detection. The extruded aluminum barrel omits external tie rods, yielding a compact, corrosion-resistant body that mounts flush, while the field-adjustable air cushioning at both ends allows technicians to tune end-of-stroke deceleration and eliminate hard mechanical impacts.
| Model | Airtac SE50 Standard Cylinder SE50X290S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø50 mm |
| Stroke | 290 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 982 N | 825 N |
| 0.7 MPa | 1374 N | — |
| Max (@1.0 MPa) | 200 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 50 | Bore size in mm. |
| ×290 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Uses the 290 mm stroke to push cartons between adjacent conveyor lanes, relying on the 982 N force to overcome friction on moving belts without stalling.
Secures aluminum engine blocks during machining, utilizing the 0.15-1.0 MPa operating range and DMSE electronic sensors to confirm clamp engagement.
Acts as a pneumatic stop in palletizing cells, where the adjustable cushion absorbs the kinetic energy of incoming loads at the end of the 290 mm extension.
When sizing this actuator, compare its 982 N push at 0.5 MPa against adjacent bores: the 40 mm variant yields 628 N, whereas the 63 mm steps up to 1559 N. This 50 mm model hits a practical sweet spot for moderate loads. If your machinery loses air pressure or the directional valve centers, note that this standard cylinder will drift and cannot hold a load vertically; integrating a BSE rod lock or external pilot check valve is required for fail-safe positioning. Furthermore, with a 290 mm stroke, the 20 mm rod and internal bearing face increased bending moments under side loads, so an external guide rail should be used to prevent premature seal wear. For direct retrofits, this cylinder shares the exact ISO 15552 mounting interface, PT1/4 port, and standard accessories of equivalent profile cylinders.
AirtacDistr lists every SE50 order code with its price on one page at https://airtacdistr.com/products/airtac-se50-iso-air-cylinder
Quick checklist
At 0.5 MPa, the SE50X290S generates 982 N of push force and 825 N of pull force. At 0.7 MPa, the push force increases to 1374 N, with a maximum push capacity of 200 kgf at 1.0 MPa. The operational speed range is 30-800 mm/s.
Yes, the SE50X290S is dimensionally interchangeable with any standard ISO 15552 profile cylinder. It shares standardized mounting dimensions, a PT1/4 port, and a 20 mm rod thread, allowing you to swap it directly into existing foot or flange mounts without machining.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.