
The AirTAC SE50 Standard Cylinder SE50X295S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø50mm bore and 295mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE50X295S is a double-acting, single-rod ISO 15552 profile cylinder engineered to deliver a 982 N push force at 0.5 MPa. Its square extruded aluminum barrel eliminates external tie rods, yielding a flush, corrosion-resistant body that mounts cleanly against machine frames. A built-in magnet comes standard, enabling direct fitment of CMSE reed or DMSE electronic sensors along the three dedicated sensor grooves.
This 50 mm bore unit travels a 295 mm stroke and features field-adjustable pneumatic cushioning at both ends. Unlike a fixed rubber bumper, the cushioning screw allows you to fine-tune end-of-stroke deceleration, absorbing kinetic energy to prevent hard mechanical impacts during high-speed cycling.
| Model | Airtac SE50 Standard Cylinder SE50X295S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø50 mm |
| Stroke | 295 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 982 N | 825 N |
| 0.7 MPa | 1374 N | — |
| Max (@1.0 MPa) | 200 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 50 | Bore size in mm. |
| ×295 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Provides the 982 N push force required to positively fold and square heavy corrugated carton flaps during high-speed packaging line transitions over the 295 mm stroke.
Extends 295 mm to route goods across adjacent conveyor belts, using the no-tie-rod profile to mount flush within narrow transfer zone side frames.
Shifts test tube racks between analysis stations, relying on the built-in magnet and DMSE electronic sensors to confirm precise end-of-stroke positioning.
Delivering 982 N of push at 0.5 MPa, this 50 mm bore fits mid-range actuation tasks. If your application requires less force, stepping down to the 40 mm bore yields 628 N of push. Conversely, moving up to the 63 mm bore provides 1559 N of thrust for heavier payloads. Because the stroke is 295 mm, the unsupported rod length increases bending moments on the front cover bearing under lateral loads; integrating an external guide rail is strongly recommended to prevent premature wear.
As a dimensionally interchangeable ISO 15552 cylinder, it serves as a direct replacement for other standard profile cylinders, sharing identical mounting footprint and PT1/4 port locations. Note that the adjustable air cushion only decelerates the piston near stroke end; it cannot hold a load vertically if air pressure is lost. For secure position holding, consider the BSE rod lock variant or an external pilot-operated check valve.
AirtacDistr lists every SE50 order code with its price on one page at https://airtacdistr.com/products/airtac-se50-iso-air-cylinder
Quick checklist
At 0.5 MPa, the SE50X295S generates 982 N of push force and 825 N of pull force. At 0.7 MPa, the push force increases to 1374 N. The maximum rated push force is 200 kgf at 1.0 MPa operating pressure.
No, the adjustable air cushion at both ends only decelerates the piston near the stroke ends and does not function as a brake or lock. If the application must hold a load without live air pressure, you must use a BSE rod lock cylinder or an external pilot-operated check valve.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.