
The AirTAC SE50 Standard Cylinder SE50X30S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø50mm bore and 30mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE50X30S is a double-acting single-rod ISO 15552 profile cylinder engineered for compact actuation. It delivers a theoretical push force of 982 N at 0.5 MPa and a maximum push of 200 kgf at 1.0 MPa, making it well-suited for short-travel positioning tasks. The integrated -S magnet enables direct mounting of CMSE reed and DMSE electronic sensors along the extruded barrel grooves for precise end-of-travel detection.
Unlike traditional tie-rod designs, the square extruded aluminum body offers a flush mounting surface that resists corrosion and simplifies bracket installation. The cylinder features field-adjustable pneumatic cushioning at both ends, allowing technicians to tune the end-of-stroke deceleration via a set screw to soften hard impacts during high-speed 30 mm movements.
| Model | Airtac SE50 Standard Cylinder SE50X30S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø50 mm |
| Stroke | 30 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 982 N | 825 N |
| 0.7 MPa | 1374 N | — |
| Max (@1.0 MPa) | 200 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 50 | Bore size in mm. |
| ×30 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Applies 982 N of push force at 0.5 MPa to secure machining spindles during high-RPM tool changes, utilizing the 30 mm stroke for rapid locking.
Drives short-travel folding arms on corrugated box packaging lines, where the -S magnet triggers DMSE sensors to confirm flap closure.
Ejects processed vials from testing carousels with a compact 30 mm extension, relying on adjustable cushioning to prevent glassware breakage.
This 50 mm bore generates 982 N of push force at 0.5 MPa. If your payload is lighter, stepping down to the 40 mm bore yields 628 N, while upgrading to the 63 mm bore provides 1559 N for heavier mechanisms. Because this is a short 30 mm stroke, side-load stress on the rod bearing is minimal, though any unsupported transverse loads still require an external guide. For retrofitting, verify the 50 mm bore, 30 mm stroke, PT1/4 port, and your required mounting accessory. Note that a standard SE cylinder will drift if air pressure is lost; use a BSE rod lock variant if the application demands fail-safe load holding.
AirtacDistr lists every SE50 order code with its price on one page at https://airtacdistr.com/products/airtac-se50-iso-air-cylinder
Quick checklist
The SE50X30S delivers a push force of 982 N and a pull force of 825 N at 0.5 MPa. At 0.7 MPa, the push force is 1374 N, with a maximum push capacity of 200 kgf at 1.0 MPa. It operates at speeds between 30 and 800 mm/s.
Yes, the SE50X30S is dimensionally interchangeable per ISO 15552 standards, serving as a direct replacement for other ISO 15552 profile cylinders without tie rods. The built-in magnet is specifically designed to work with AirTAC CMSE reed and DMSE electronic solid-state sensors mounted in the barrel grooves.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.