
The AirTAC SE50 Standard Cylinder SE50X325S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø50mm bore and 325mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE50X325S is a double-acting single-rod profile cylinder built to ISO 15552 dimensions, delivering a push force of 982 N at 0.5 MPa. Its square extruded aluminum barrel omits external tie rods, yielding a compact footprint that mounts flush against machine frames while resisting corrosion. The integrated -S magnet enables precise end-of-stroke detection using AirTAC CMSE reed or DMSE electronic sensors.
Field-adjustable pneumatic cushioning at both ends allows you to tune the end-of-stroke deceleration via a set screw, softening hard impacts when cycling at speeds up to 800 mm/s. Because this is a 325 mm stroke unit, the 20 mm hard-chrome rod experiences greater leverage on the guide bearing under side loads, making an external linear guide essential for maintaining seal longevity.
| Model | Airtac SE50 Standard Cylinder SE50X325S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø50 mm |
| Stroke | 325 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 982 N | 825 N |
| 0.7 MPa | 1374 N | — |
| Max (@1.0 MPa) | 200 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 50 | Bore size in mm. |
| ×325 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Uses the 325 mm stroke to extend a diverting flap on a packaging conveyor, relying on the 982 N push force to reliably redirect heavy cartons without stalling.
Opens and closes a sliding machine tool safety door, utilizing the built-in magnet and DMSE electronic sensors to confirm door closure before the cycle starts.
Drives a mechanical arm to fold corrugated cardboard flaps on a carton sealing line, where the adjustable end cushions prevent jarring that could tear the material.
This 50 mm bore generates 982 N push at 0.5 MPa. If your application requires less force, the 40 mm neighbor provides 628 N; if you need more clamping power, stepping up to the 63 mm bore yields 1559 N. As an ISO 15552 profile cylinder, it serves as a direct dimensional replacement for any standard 50 mm cylinder with a PT1/4 port and 325 mm stroke.
Note that the standard adjustable air cushion only decelerates the piston near stroke end; it does not hold a load. If air pressure drops or the valve centers, the rod will drift. For positive position holding, consider a BSE rod-lock variant or an external pilot-operated check valve.
AirtacDistr lists every SE50 order code with its price on one page at https://airtacdistr.com/products/airtac-se50-iso-air-cylinder
Quick checklist
At 0.5 MPa, the push force is 982 N and the pull force is 825 N. At 0.7 MPa, the push force is 1374 N. The maximum push force is 200 kgf at 1.0 MPa.
Yes. The SE50X325S shares the exact ISO 15552 mounting interface, 50 mm bore, 325 mm stroke, and PT1/4 port dimensions, making it a direct retrofit for any standard ISO 15552 profile cylinder.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.