
The AirTAC SE50 Standard Cylinder SE50X350 is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø50mm bore and 350mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE50X350 is a double-acting, single-rod ISO 15552 profile cylinder engineered to deliver 982 N of push force at 0.5 MPa and 1374 N at 0.7 MPa. Its square extruded aluminum barrel eliminates external tie rods, yielding a flush, corrosion-resistant exterior that simplifies direct mounting and spatial integration within tight machine envelopes.
This 50 mm bore unit features a 20 mm hard-chrome plated steel rod and a PT1/4 port. Field-adjustable pneumatic cushioning at both stroke ends allows technicians to tune end-of-stroke deceleration via a set screw, mitigating impact shock at operating speeds up to 800 mm/s. As this specific SKU lacks the -S magnet suffix, it is not equipped from the factory for AirTAC CMSE or DMSE electronic position sensing.
| Model | Airtac SE50 Standard Cylinder SE50X350 |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø50 mm |
| Stroke | 350 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 982 N | 825 N |
| 0.7 MPa | 1374 N | — |
| Max (@1.0 MPa) | 200 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 50 | Bore size in mm. |
| ×350 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Provides the 982 N push at 0.5 MPa required to cleanly fold and secure heavy corrugated cardboard flaps on continuous-motion packaging lines, utilizing the 350 mm stroke for wide-format cartons.
Shifts heavy timber or steel pallets across transfer sections, leveraging the 350 mm stroke to clear adjacent conveyor lanes while the adjustable cushion softens the diverting impact at high speed.
Drives a 350 mm linear displacement to rotate multi-position sample carousels in analytical instrumentation, where the smooth extruded profile allows flush mounting to the machine frame without tie-rod interference.
Delivering 982 N push at 0.5 MPa, this model is correctly sized for moderate-load actuation. If your application requires less force, stepping down to the 40 mm bore yields 628 N push, whereas upgrading to the 63 mm bore provides 1559 N for heavier payloads. For direct ISO 15552 retrofits, verify the 350 mm stroke, PT1/4 port, and required mounting accessory.
Because the 350 mm stroke generates extended leverage, the 20 mm rod and internal bearing face increased bending moments under side loads; an external guide rail is strongly recommended to prevent premature wear. Furthermore, the adjustable air cushion only decelerates the piston near the end of travel—it is not a locking mechanism. If the machinery must hold a vertical load or resist drift upon air loss, pair this cylinder with an external pilot-operated check valve or explore the AirTAC BSE rod-lock series.
AirtacDistr lists every SE50 order code with its price on one page at https://airtacdistr.com/products/airtac-se50-iso-air-cylinder
Quick checklist
The SE50X350 generates 982 N of push force and 825 N of pull force at 0.5 MPa. At 0.7 MPa, the push force is 1374 N, and the maximum push force is 200 kgf at 1.0 MPa. The operating speed range for this 50 mm bore cylinder is 30-800 mm/s.
Yes, the SE50X350 adheres strictly to ISO 15552 / VDMA 24562 mounting interface standards, making it dimensionally interchangeable with other ISO 15552 profile cylinders. It features a PT1/4 port and a 20 mm rod, but note this specific SKU lacks the -S magnet for position sensing.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.