
The AirTAC SE50 Standard Cylinder SE50X380S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø50mm bore and 380mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE50X380S is a double-acting single-rod ISO 15552 profile cylinder engineered to deliver a 982 N push force at 0.5 MPa across a 380 mm stroke. Its square extruded aluminum barrel eliminates external tie rods, yielding a compact, corrosion-resistant body that mounts flush against machine frames while protecting internal components.
Equipped with a built-in magnetic piston (-S), this unit seamlessly integrates with AirTAC CMSE reed and DMSE electronic sensors for precise end-of-stroke detection. The field-adjustable pneumatic cushioning at both ends allows technicians to tune deceleration via a set screw, softening hard impacts when cycling at speeds up to 800 mm/s.
| Model | Airtac SE50 Standard Cylinder SE50X380S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø50 mm |
| Stroke | 380 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 982 N | 825 N |
| 0.7 MPa | 1374 N | — |
| Max (@1.0 MPa) | 200 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 50 | Bore size in mm. |
| ×380 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Deploys a 380 mm reach to push corrugated cartons between sorting lanes, utilizing the 982 N push force to overcome side friction without stalling.
Raises heavy packaging film rolls to the unwind spindle, relying on the 825 N pull force to retract the tooling securely during high-speed wrapping cycles.
Shifts automated analyzer carriages precisely between test stations, using the integrated magnet to trigger DMSE electronic sensors for positional confirmation.
When sizing this 50 mm bore, stepping down to a 40 mm cylinder reduces the 0.5 MPa push to 628 N, while stepping up to a 63 mm bore increases it to 1559 N. This SE50X380S provides a balanced middle ground for mid-range actuation. Because the 380 mm stroke creates an extended lever arm, external guides are recommended to prevent rod-bearing bending under heavy lateral loads.
As a true ISO 15552 profile cylinder, it serves as a direct replacement sharing standard mounting dimensions and PT1/4 ports. Note that the adjustable air cushion only decelerates the piston near stroke end; if your process must hold a vertical load without live air pressure, you must integrate an external rod lock like the BSE series or a pilot-operated check valve.
AirtacDistr lists every SE50 order code with its price on one page at https://airtacdistr.com/products/airtac-se50-iso-air-cylinder
Quick checklist
At 0.5 MPa, this 50 mm bore cylinder provides 982 N of push force and 825 N of pull force. At 0.7 MPa, the push force is 1374 N, with a maximum push capacity of 200 kgf at 1.0 MPa. The operational speed range is 30-800 mm/s.
Yes, the SE50X380S shares the exact ISO 15552 / VDMA 24562 mounting interface and PT1/4 port dimensions, making it a direct replacement for other ISO 15552 profile cylinders. You can retain your existing mounting hardware and sensor brackets.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.