verified AirTAC China Authorized Export Seller shield 100% Genuine AirTAC Parts workspace_premium 1-Year Warranty
appsShop by Modelexpand_more
person shopping_cart Request a QuoteQuote
AirTAC SE Series · ISO 15552 Cylinder

Airtac SE50 Standard Cylinder SE50X400S

The AirTAC SE50 Standard Cylinder SE50X400S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø50mm bore and 400mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.

  • BoreØ50 mm
  • Stroke400 mm
  • Port sizePT1/4
  • Acting typeDouble acting
  • Rod threadM16×1.5
  • CushionAdjustable, 30 mm
$110.49 $117.99Save 6% Standard model — usually dispatched in 3-5 days
Request a Quote
  • No minimum order. A single piece can be ordered.
  • Shipped from our own warehouse: most standard models dispatch in 3–5 days; custom and non-standard models take 8–10 business days. Transit time after that depends on the destination.
Compare every SE50 stroke, mounting and version on one page All SE50 codes →
verified Genuine AirTAC workspace_premium 1-year warranty bolt Reply in 7 h

About the Airtac SE50 Standard Cylinder SE50X400S

The AirTAC SE50X400S is a double-acting, single-rod ISO 15552 profile cylinder engineered to deliver 982 N of push force at 0.5 MPa and a maximum of 200 kgf at 1.0 MPa. Driven by filtered air through a PT1/4 port, it operates reliably across a 0.15-1.0 MPa pressure range and achieves cycling speeds of 30-800 mm/s. The extruded aluminum barrel omits external tie rods entirely, presenting a clean, corrosion-resistant exterior that mounts flush against machine frames while protecting internal mechanics from workshop debris.

This 400 mm stroke unit features a 20 mm hard-chrome plated rod with an M16x1.5 thread, and includes a built-in magnet (-S) for seamless integration with AirTAC CMSE reed and DMSE electronic position sensors. To absorb kinetic energy at the stroke extremes, field-adjustable air cushions at both ends allow technicians to fine-tune end-of-stroke deceleration via a dedicated needle screw, softening hard mechanical impacts during high-speed actuation rather than relying on a fixed rubber bumper.

Airtac SE50 Standard Cylinder SE50X400S Technical Specifications

ModelAirtac SE50 Standard Cylinder SE50X400S
SeriesSE ISO 15552 profile cylinder
Bore sizeØ50 mm
Stroke400 mm
Acting typeDouble acting
Port sizePT1/4
Rod threadM16×1.5
FluidAir (filtered by 40µm element)
Operating pressure0.15 – 1.0 MPa
Proof pressure1.5 MPa
Temperature-20 to +70 °C (0–150 °C with FKM seals)
Speed range30 – 800 mm/s
CushionAdjustable, 30 mm
Max strokeUp to 1200 mm

Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).

Theoretical Output Force (Ø50mm)

PressurePush forcePull force
0.5 MPa982 N825 N
0.7 MPa1374 N—
Max (@1.0 MPa)200 kgf

Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.

Model Code: Airtac SE50 Standard Cylinder SE50X400S

SEISO 15552 / VDMA 24562 profile-barrel double-acting cylinder.
50Bore size in mm.
×400Stroke length in mm.
-SOptional built-in magnet for CMSE / DMSE sensor sensing.

Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).

Where the Airtac SE50 Standard Cylinder SE50X400S Is Used

conveyor_belt

Pallet Diverting Gate

Leveraging the 982 N push force and 400 mm stroke, this cylinder extends a diverting arm on a packaging conveyor to reroute heavy cardboard cartons into secondary processing lanes.

factory

Injection Mold Ejection

Uses the 30 mm adjustable cushion to gently decelerate the 20 mm rod at the end of a 400 mm extraction stroke, safely pulling finished plastic automotive components from a mold cavity.

warehouse

Vertical Parts Elevator

Raises stacked tote bins between conveyor tiers; the built-in magnet triggers a DMSE electronic sensor to confirm the 400 mm upward stroke is complete before the lower feed mechanism discharges.

Is the Airtac SE50 Standard Cylinder SE50X400S the Right Cylinder?

Delivering 982 N push at 0.5 MPa, this 50 mm bore cylinder is sized for medium-duty positioning and lifting. If your application requires less force, stepping down to the 40 mm bore variant yields 628 N of push, conserving compressed air. Conversely, upgrading to the 63 mm bore provides 1559 N of push for heavier payloads. Because this is a double-acting cylinder, it does not hold its position or support a load if air pressure is lost or the directional valve is centered; the piston will drift. For fail-safe load holding, consider the AirTAC BSE series with an integrated rod lock.

At 400 mm of stroke, the unsupported length of the 20 mm rod introduces a risk of bearing bending under lateral loads. To prevent premature seal wear and rod deformation, implement an external linear guide to absorb side forces and keep the actuator purely linear. The standardized ISO 15552 mounting interface ensures dimensional interchangeability with other profile cylinders, allowing you to reuse existing FA front flange or LB foot mounting hardware. The integrated -S magnet enables direct installation of CMSE or DMSE sensors for end-of-stroke confirmation.

AirtacDistr lists every SE50 order code with its price on one page at https://airtacdistr.com/products/airtac-se50-iso-air-cylinder

Quick checklist

  • ✓ Required force at your working pressure
  • ✓ Stroke and mounting space
  • ✓ Port/thread type (PT/G)
  • ✓ Magnet (-S) for CMSE/DMSE sensors?
  • ✓ Side load — consider a guided cylinder
Ask an Engineer

Installation & Maintenance Notes

  • check Use clean air filtered to 40µm or finer.
  • check Keep within 0.15 – 1.0 MPa operating pressure.
  • check Avoid side load on the piston rod.
  • check Adjust end cushion screws for smooth stops.
  • check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
  • check Installation by qualified personnel per AirTAC docs.

Airtac SE50 Standard Cylinder SE50X400S FAQ

The SE50X400S generates 982 N of push force and 825 N of pull force at 0.5 MPa, and 1374 N of push force at 0.7 MPa. The maximum push force is 200 kgf at 1.0 MPa. It features a PT1/4 port, a 20 mm rod diameter, and an M16x1.5 rod-end thread.

Yes, the SE50X400S is manufactured to the ISO 15552 / VDMA 24562 standard, making its mounting dimensions fully interchangeable with other profile cylinders of the same bore size. This allows you to drop it into existing machinery without modifying the FA front flange or LB foot bracket geometry, while retaining the use of AirTAC CMSE and DMSE sensors via the built-in magnet.

verified

Authorized Export Seller

Genuine AirTAC parts produced by AirTAC factory.

workspace_premium

1-Year Warranty

Covers non-human-caused product damage.

local_shipping

Fast Dispatch

Most standard models are dispatched in 3-5 days.

bolt

Fast Reply

Most inquiries answered within 7 hours.

Related AirTAC SE Cylinders

Request a Quote for Airtac SE50 Standard Cylinder SE50X400S

Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.

Thank you. We received your request for SE50X400S and will confirm price, availability and lead time — usually within 7 hours.

For the fastest response, keep the complete model number above and include a clear photo of the product label. If photo upload is unavailable, email photos to [email protected] with your model number.