
The AirTAC SE50 Standard Cylinder SE50X420S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø50mm bore and 420mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE50X420S is a double-acting single-rod ISO 15552 profile cylinder engineered to deliver 982 N of push force at 0.5 MPa. Its square extruded aluminum barrel eliminates external tie rods, yielding a compact, corrosion-resistant body that mounts flush against machine frames while freeing up the lateral surfaces for sensor placement.
This specific unit includes a built-in magnet (-S) for non-contact position detection using AirTAC CMSE reed or DMSE electronic switches. To protect the piston at high cycling speeds, field-adjustable air cushions at both ends allow you to dial in the exact deceleration required for the 420 mm travel, preventing hard end-stop impacts.
| Model | Airtac SE50 Standard Cylinder SE50X420S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø50 mm |
| Stroke | 420 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 982 N | 825 N |
| 0.7 MPa | 1374 N | — |
| Max (@1.0 MPa) | 200 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 50 | Bore size in mm. |
| ×420 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Provides the 982 N push force needed to actuate a heavy mechanical divert gate on a 50 mm conveyor line, using its 420 mm stroke to clear the pallet path fully.
Drives the mechanical arms on a case packing machine, relying on the 30 mm adjustable end-cushion to gently fold heavy cardboard flaps without crushing the product.
Feeds sheet metal blanks into a press brake, utilizing the integrated -S magnet and DMSE sensor to confirm the pusher has retracted fully before the press cycles.
At 0.5 MPa, this 50 mm bore generates 982 N of push force. If your payload is lighter, stepping down to the 40 mm bore drops the output to 628 N, saving valuable air consumption and physical footprint. For heavier dynamic loads, stepping up to the 63 mm bore increases the push force to 1559 N. Because this is a standard ISO 15552 profile cylinder, it serves as a direct dimensional replacement for any compliant brand, matching standard mounting hardware and center distances.
With a 420 mm stroke, the Ø20 mm rod and its bearing face a higher risk of bending under lateral stress. For applications that cannot guarantee perfectly axial load alignment, incorporating an external linear guide is strongly recommended to prevent premature seal wear. Furthermore, note that the adjustable air cushion only decelerates the piston near stroke end; it does not lock or hold the load if air pressure is lost.
AirtacDistr lists every SE50 order code with its price on one page at https://airtacdistr.com/products/airtac-se50-iso-air-cylinder
Quick checklist
The SE50X420S has a 50 mm bore and uses a PT1/4 port with an M16x1.5 rod-end thread. At 0.5 MPa it delivers 982 N push and 825 N pull. At 0.7 MPa the push force is 1374 N, and it reaches a maximum push of 200 kgf at 1.0 MPa.
No, the air cushion only decelerates the piston near the stroke ends and does not function as a mechanical brake. If air is lost or the valve is centered, the piston will drift under load. To hold a vertical load without live pressure, you would need an external rod lock or a pilot-operated check valve.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.