
The AirTAC SE50 Standard Cylinder SE50X430S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø50mm bore and 430mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE50X430S is a double-acting single-rod ISO 15552 profile cylinder engineered for a 50mm bore and a 430mm stroke. It delivers a robust 982 N push force at 0.5 MPa, making it well-suited for mid-range automation tasks. The extruded aluminum barrel design omits external tie rods, yielding a compact, corrosion-resistant body that mounts flush against machinery frames while maintaining the standardized ISO 15552 mounting interface.
This specific configuration includes a built-in magnet (-S) for seamless integration with AirTAC CMSE reed and DMSE electronic position sensors. To protect payloads during high-speed cycling up to 800 mm/s, the cylinder features field-adjustable pneumatic air cushioning at both ends, allowing technicians to precisely tune end-of-stroke deceleration instead of relying on harsh fixed bumpers.
| Model | Airtac SE50 Standard Cylinder SE50X430S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø50 mm |
| Stroke | 430 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 982 N | 825 N |
| 0.7 MPa | 1374 N | — |
| Max (@1.0 MPa) | 200 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 50 | Bore size in mm. |
| ×430 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Uses the 982 N push force at 0.5 MPa to reliably pivot a diverting arm on a packaging conveyor line, with the 430mm stroke providing the reach needed to clear wide product lanes.
Leverages the built-in magnet with DMSE electronic sensors to confirm fully open and closed safety doors, while the tie-rod-free profile mounts flush to the machine enclosure.
Applies a controlled clamping load to test components, utilizing the field-adjustable air cushions to soften the platen stop at high operating speeds.
Selecting this 50mm bore provides 982 N of push force at 0.5 MPa. If your application requires less force, stepping down to the 40mm bore yields 628 N of push, whereas stepping up to the 63mm bore provides 1559 N. Keep in mind that a standard SE cylinder does not hold its load when air pressure is lost; if your 430mm stroke application requires true position holding during an air loss or valve centering event, you must integrate an external rod lock like the BSE series or a pilot-operated check valve.
Because the 430mm stroke creates a long unsupported lever arm, side loads will induce significant bending moments on the M16x1.5 rod thread and the internal rod bearing. Even with the 30mm adjustable cushion at both ends, an external guide rail must be used to prevent premature seal wear and binding. For a direct replacement, match the 50mm bore, 430mm stroke, PT1/4 port, and the -S magnet requirement.
AirtacDistr lists every SE50 order code with its price on one page at https://airtacdistr.com/products/airtac-se50-iso-air-cylinder
Quick checklist
The SE50X430S has a 50mm bore and uses a PT1/4 port. At 0.5 MPa it provides 982 N of push force and 825 N of pull force. At 0.7 MPa the push force is 1374 N, and the maximum push force is 200 kgf at 1.0 MPa.
Yes, it is dimensionally interchangeable with other ISO 15552 profile cylinders for direct retrofits. However, it is a double-acting cylinder and does not hold its load if air is lost; you would need a BSE rod lock variant for secure position holding.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.