
The AirTAC SE50 Standard Cylinder SE50X450S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø50mm bore and 450mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE50X450S is a double-acting, single-rod ISO 15552 profile cylinder engineered to deliver a robust 982 N push force at 0.5 MPa. Its clean, extruded aluminum barrel completely eliminates external tie rods, presenting a flush, corrosion-resistant exterior that simplifies mounting and reduces debris buildup in tight machinery layouts.
Equipped with a built-in magnet (-S), this unit is fully primed for non-contact position monitoring using AirTAC CMSE reed or DMSE electronic sensors. Furthermore, the field-adjustable pneumatic cushioning at both stroke ends allows technicians to fine-tune end-of-stroke deceleration, effectively neutralizing impact shock when cycling 450 mm at speeds up to 800 mm/s.
| Model | Airtac SE50 Standard Cylinder SE50X450S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø50 mm |
| Stroke | 450 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 982 N | 825 N |
| 0.7 MPa | 1374 N | — |
| Max (@1.0 MPa) | 200 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 50 | Bore size in mm. |
| ×450 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Provides the 982 N push and 450 mm stroke needed to open and fold heavy corrugated carton flaps on continuous packaging lines.
Positions sheet metal backgauges on press brakes, utilizing the 450 mm travel and built-in magnet for precise DMSE sensor feedback.
Actuates a mechanical divert arm to reroute heavy pallets between conveyor lanes, relying on the adjustable cushion to soften stops.
Delivering 982 N of push force at 0.5 MPa, this 50 mm bore is highly versatile. If your application requires less energy, stepping down to the 40 mm bore yields 628 N of push, whereas moving up to the 63 mm bore provides a substantial 1559 N. Because this is a double-acting cylinder, it cannot hold a load unpowered—air loss causes drift, so an external BSE rod lock is necessary for strict position holding.
At 450 mm of stroke, the 20 mm rod and front bearing face increased bending moments under lateral loads; incorporating an external guide rail is strongly advised to prevent premature seal wear. As a dimensionally interchangeable ISO 15552 component, it serves as a direct replacement for other ISO 15552 cylinders, matching the PT1/4 port, 450 mm stroke, and standard mounting accessories.
AirtacDistr lists every SE50 order code with its price on one page at https://airtacdistr.com/products/airtac-se50-iso-air-cylinder
Quick checklist
The SE50X450S generates 982 N push and 825 N pull at 0.5 MPa, 1374 N push at 0.7 MPa, and reaches a maximum push of 200 kgf at 1.0 MPa.
Yes, the SE50X450S shares the exact ISO 15552 mounting interface and PT1/4 port, allowing it to direct replace other ISO 15552 profile cylinders without modifying the machine frame.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.