
The AirTAC SE50 Standard Cylinder SE50X45S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø50mm bore and 45mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE50X45S is a double-acting single-rod profile cylinder built to the ISO 15552 standard, delivering a push force of 982 N at 0.5 MPa and a maximum output of 200 kgf. Its short 45 mm stroke makes it highly effective for compact clamping and ejecting tasks where space is restricted but decisive force is still required.
Because this variant includes the -S magnet, it is fully ready for position sensing using AirTAC CMSE reed or DMSE electronic switches. The extruded aluminum barrel omits external tie rods, yielding a clean, flush-mounting surface that resists debris accumulation and simplifies sensor placement along the three integrated grooves.
| Model | Airtac SE50 Standard Cylinder SE50X45S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø50 mm |
| Stroke | 45 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 982 N | 825 N |
| 0.7 MPa | 1374 N | — |
| Max (@1.0 MPa) | 200 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 50 | Bore size in mm. |
| ×45 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Applies 982 N of clamping force at 0.5 MPa to secure aluminum engine blocks during CNC milling, utilizing the short 45 mm stroke for rapid actuation.
Executes quick folding strokes on corrugated packaging lines, where the compact profile and adjustable end cushions prevent harsh impacts at the stroke limits.
Uses the integrated -S magnet with DMSE sensors to confirm paddle position, accurately routing mixed SKUs on high-speed logistics conveyors.
When sizing this actuator, compare its 982 N push at 0.5 MPa against its neighbors: the 40 mm bore provides 628 N, while the 63 mm bore steps up to 1559 N. This positions the 50 mm bore perfectly for medium-duty tasks that would stall a smaller cylinder but do not warrant the bulk of a 63 mm unit. It is dimensionally interchangeable with other ISO 15552 cylinders, allowing a direct retrofit using existing mounting hardware.
Note that a standard double-acting cylinder drifts when air pressure is removed or a valve is centered, so the adjustable air cushions at both ends only decelerate the piston near stroke end rather than locking the load. If your process demands positive holding without live air pressure, consider pairing this with an external pilot-operated check valve or exploring the BSE rod-lock variant.
AirtacDistr lists every SE50 order code with its price on one page at https://airtacdistr.com/products/airtac-se50-iso-air-cylinder
Quick checklist
The 50 mm bore provides a push force of 982 N and a pull force of 825 N at 0.5 MPa. At 0.7 MPa, the push force is 1374 N, with a maximum push capacity of 200 kgf at 1.0 MPa. This model uses a PT1/4 port and operates at speeds between 30 and 800 mm/s.
Yes, the SE50X45S is dimensionally interchangeable per ISO 15552 standards. You can drop it in as a replacement for other ISO 15552 profile cylinders using the same mounting accessories, and the built-in magnet allows seamless integration with AirTAC CMSE or DMSE position sensors.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.