
The AirTAC SE50 Standard Cylinder SE50X475S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø50mm bore and 475mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE50X475S is a double-acting, single-rod ISO 15552 profile cylinder engineered for precise linear motion. It delivers a robust 982 N push force at 0.5 MPa alongside an 825 N retract pull, making it well-suited for mid-range automation tasks. The integrated -S magnet enables direct mounting of CMSE reed and DMSE electronic sensors along the extruded aluminum barrel.
Because it utilizes a square extruded profile without external tie rods, the body is inherently more compact and corrosion-resistant than round-body alternatives. The field-adjustable pneumatic cushioning at both ends allows technicians to fine-tune end-of-stroke deceleration via a set screw, effectively absorbing kinetic energy before impact rather than relying on a fixed rubber bumper.
| Model | Airtac SE50 Standard Cylinder SE50X475S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø50 mm |
| Stroke | 475 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 982 N | 825 N |
| 0.7 MPa | 1374 N | — |
| Max (@1.0 MPa) | 200 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 50 | Bore size in mm. |
| ×475 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Drives the folding mechanism on case erectors, utilizing the 475 mm stroke and 982 N push force to open and seal corrugated cardboard flaps smoothly.
Actuates routing gates on conveyor lines, relying on the adjustable cushion to decelerate the 50 mm bore smoothly without jarring the pallet load.
Shifts secondary tooling racks in automated machining centers, using the built-in magnet to trigger DMSE sensors for position verification.
When sizing this actuator, consider stepping down to a 40 mm bore if your application requires only 628 N of push force at 0.5 MPa, or moving up to a 63 mm bore if you need the 1559 N thrust capacity for heavier payloads. As a true ISO 15552 profile cylinder, the SE50X475S is dimensionally interchangeable with other ISO 15552 cylinders, allowing a seamless direct retrofit using standardized mounting hardware and its PT1/4 port.
With a 475 mm stroke, the 20 mm diameter piston rod experiences higher bending moments under side loads. For applications spanning this distance, incorporating an external guide rail is strongly recommended to prevent rod-bearing wear. Note that the adjustable air cushion only decelerates the piston near stroke end; it does not hold the load if air pressure is lost. For position holding without live pressure, explore a BSE rod lock variant.
AirtacDistr lists every SE50 order code with its price on one page at https://airtacdistr.com/products/airtac-se50-iso-air-cylinder
Quick checklist
The SE50X475S provides a push force of 982 N and a pull force of 825 N at 0.5 MPa. At 0.7 MPa, the push force increases to 1374 N. The maximum push force is 200 kgf at 1.0 MPa, and the operational speed ranges from 30 to 800 mm/s.
Yes, the SE50X475S is a standard ISO 15552 profile cylinder, making it dimensionally interchangeable with other ISO 15552 cylinders. It shares the standardized mounting interface and PT1/4 porting, allowing a direct replacement without extensive machinery modifications.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.