
The AirTAC SE50 Standard Cylinder SE50X480S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø50mm bore and 480mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE50X480S is a double-acting single-rod ISO 15552 profile cylinder delivering 982 N of push force at 0.5 MPa. Its square extruded aluminum barrel eliminates external tie rods, yielding a compact, corrosion-resistant body that mounts flush on automated lines. The built-in magnet enables direct position tracking with CMSE reed or DMSE electronic sensors.
Field-adjustable air cushions at both ends let you precisely tune end-of-stroke deceleration, softening hard impacts during high-speed 480 mm travel. Operating pressure spans 0.15-1.0 MPa, and the PT1/4 port pairs with a 20 mm hard-chrome rod for reliable linear motion.
| Model | Airtac SE50 Standard Cylinder SE50X480S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø50 mm |
| Stroke | 480 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 982 N | 825 N |
| 0.7 MPa | 1374 N | — |
| Max (@1.0 MPa) | 200 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 50 | Bore size in mm. |
| ×480 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Uses the 982 N push force and 480 mm stroke to pivot heavy cardboard cartons across packaging conveyor lanes at high speed.
Extends the full 480 mm to open safety blast doors on enclosed CNC lathes, relying on adjustable cushions to prevent slamming.
Lifts tier-1 pallets in low-headroom distribution hubs, using the -S magnet and DMSE sensors to confirm upper deck positioning.
This 50 mm bore generates 982 N push at 0.5 MPa; if your load is lighter, step down to the 40 mm bore (628 N push), or step up to the 63 mm bore (1559 N push) for heavier demands. As a standard double-acting cylinder, it will drift if air pressure is lost—use a BSE rod lock for fail-safe holding. At 480 mm of stroke, the unsupported piston rod is highly susceptible to side-load bending; always mount an external guide to prevent premature rod-bearing wear. For ISO 15552 dimensional interchangeability, match the 50 mm bore, 480 mm stroke, PT1/4 port, and mounting accessory.
AirtacDistr lists every SE50 order code with its price on one page at https://airtacdistr.com/products/airtac-se50-iso-air-cylinder
Quick checklist
At 0.5 MPa it provides 982 N push and 825 N pull; at 0.7 MPa it provides 1374 N push. The maximum push force is 200 kgf at 1.0 MPa. Operating speed ranges from 30-800 mm/s.
No. The adjustable air cushion only decelerates the piston near stroke end; it is not a brake. If live air is lost, the rod will drift. For true position holding, use a BSE rod lock or an external pilot-operated check valve.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.