
The AirTAC SE50 Standard Cylinder SE50X500SH is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø50mm bore and 500mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE50X500SH is a double-acting single-rod ISO 15552 profile cylinder engineered for 500 mm stroke applications. It generates 982 N of push force and 825 N of pull force at 0.5 MPa, making it well-suited for mid-range automation tasks. The square extruded aluminum barrel eliminates external tie rods, yielding a compact, corrosion-resistant body that mounts flush against machinery frames.
Equipped with a Viton (FKM) seal, this unit reliably operates in environments up to 150 C where standard TPU seals would fail. The integrated -S magnet supports position detection via AirTAC CMSE reed or DMSE electronic sensors, while field-adjustable air cushioning at both ends lets you fine-tune end-of-stroke deceleration to prevent hard impacts.
| Model | Airtac SE50 Standard Cylinder SE50X500SH |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø50 mm |
| Stroke | 500 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 982 N | 825 N |
| 0.7 MPa | 1374 N | — |
| Max (@1.0 MPa) | 200 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 50 | Bore size in mm. |
| ×500 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Handles the 500 mm extraction stroke of hot plastic sheets from forming presses, utilizing the FKM seal to withstand ambient 150 C radiant heat while delivering 982 N of push.
Pushes heavy glassware or deflectors along high-temperature conveyor lines, relying on the 825 N pull force and the Viton seal to resist thermal degradation.
Secures cast engine blocks during CNC machining, using the integrated -S magnet with DMSE sensors to verify 500 mm travel completion before cutting cycles start.
At 0.5 MPa, this 50 mm bore provides 982 N of push force. If your application requires less force, the 40 mm bore offers 628 N of push, whereas stepping up to the 63 mm bore yields 1559 N. Because the 500 mm stroke is substantial, the Ø20 mm rod and internal bearing face bending stress under side loads; always use an external guide to prevent premature wear. As a standard ISO 15552 profile cylinder, it serves as a direct dimensional replacement for other ISO 15552 cylinders sharing the same 50 mm bore, 500 mm stroke, PT1/4 port, and standard mounting accessories.
Note that this cylinder does not hold its load when air pressure is lost or the valve is centered, as the piston will drift. The adjustable air cushion only decelerates the piston near the stroke ends and does not act as a locking mechanism.
AirtacDistr lists every SE50 order code with its price on one page at https://airtacdistr.com/products/airtac-se50-iso-air-cylinder
Quick checklist
The 50 mm bore provides 982 N push and 825 N pull at 0.5 MPa, 1374 N push at 0.7 MPa, and a maximum push of 200 kgf at 1.0 MPa.
No, a standard double-acting cylinder will drift if air is lost or the valve is centered. The adjustable air cushion only decelerates the piston near stroke end; for true load holding, you need a BSE rod lock or an external pilot-operated check valve.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.