
The AirTAC SE50 Standard Cylinder SE50X50SG is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø50mm bore and 50mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE50X50SG is a double-acting, single-rod ISO 15552 profile cylinder delivering 982 N of push force at 0.5 MPa and 1374 N at 0.7 MPa. It features a 50 mm bore, a 50 mm stroke, and a G1/4 BSPP port. The square extruded aluminum barrel eliminates external tie rods, yielding a compact, corrosion-resistant body that mounts flush against machine frames while resisting mechanical snags.
This specific configuration includes a built-in magnet (-S) for direct compatibility with AirTAC CMSE reed and DMSE electronic sensors, ensuring reliable end-of-stroke detection. The field-adjustable air cushioning at both ends allows technicians to tune the pneumatic deceleration via a set screw, softening hard end stops during high-speed cycling. The cushion only decelerates the piston near stroke end and does not lock or hold the load.
| Model | Airtac SE50 Standard Cylinder SE50X50SG |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø50 mm |
| Stroke | 50 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 982 N | 825 N |
| 0.7 MPa | 1374 N | — |
| Max (@1.0 MPa) | 200 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 50 | Bore size in mm. |
| ×50 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Drives the folding mechanism on packaging lines, utilizing its 982 N push force to snap heavy cardboard carton flaps into position securely before sealing.
Powers a routing diverter on a conveyor belt system, using its 50 mm stroke and built-in DMSE sensor confirmation to push parcels smoothly onto secondary chutes.
Actuates an electronic test bed fixture, applying precise 825 N pull force to hold circuit boards against spring-loaded test pins during automated quality checks.
When sizing this 50 mm bore actuator, evaluate your exact force requirements: it provides 982 N push at 0.5 MPa. If your assembly requires less force, step down to the 40 mm bore, which yields 628 N of push at 0.5 MPa. If your mechanism demands higher thrust, the 63 mm bore offers 1559 N at 0.5 MPa. Because this is a double-acting cylinder, it does not hold its position if air pressure is lost or the valve is centered—the piston will drift, so a BSE rod lock is needed for secure holding.
As a dimensionally interchangeable ISO 15552 cylinder, it serves as a direct replacement for other ISO 15552 cylinders, sharing standard mounting hardware. This SE50X50SG variant includes a G1/4 port thread, a built-in position-sensing magnet, and standard mounting brackets. At a 50 mm stroke, side-load stress on the rod bearing is minimal, but always ensure the load is guided externally to prevent premature seal wear.
AirtacDistr lists every SE50 order code with its price on one page at https://airtacdistr.com/products/airtac-se50-iso-air-cylinder
Quick checklist
The SE50X50SG provides 982 N push and 825 N pull at 0.5 MPa, 1374 N push at 0.7 MPa, and a maximum push of 200 kgf at 1.0 MPa. Its operating speed range is 30-800 mm/s.
Yes, the SE50X50SG is dimensionally interchangeable per the ISO 15552 standard. It shares the standardized mounting interface and hardware dimensions, making it a direct replacement for other ISO 15552 profile cylinders.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.