
The AirTAC SE50 Standard Cylinder SE50X550S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø50mm bore and 550mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE50X550S is a double-acting single-rod profile cylinder operating at 982 N push and 825 N pull at 0.5 MPa. Built to the ISO 15552 standard, its square extruded aluminum barrel omits external tie rods, yielding a compact footprint that mounts flush against machine frames while resisting corrosion. The integrated -S magnet enables direct position tracking using CMSE reed or DMSE electronic sensors.
Field-adjustable pneumatic cushioning at both stroke ends allows you to tune deceleration via a set screw, softening hard impacts when cycling at speeds up to 800 mm/s. With a 50 mm bore, 20 mm rod, and PT1/4 porting, this 550 mm stroke unit provides robust linear motion for mid-force assembly tasks.
| Model | Airtac SE50 Standard Cylinder SE50X550S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø50 mm |
| Stroke | 550 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 982 N | 825 N |
| 0.7 MPa | 1374 N | — |
| Max (@1.0 MPa) | 200 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 50 | Bore size in mm. |
| ×550 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Uses the 550 mm stroke and 982 N push force to extend a diverter arm across a packaging line, reliably redirecting heavy cardboard cartons at high cycling speeds.
Maintains precise tension on a shrink-wrap film roll via the 825 N retract force, while the -S magnet triggers DMSE electronic sensors to confirm material feed.
Actuates a mid-stroke gating mechanism on a pallet assembly conveyor, utilizing the adjustable end cushions to soften the impact of the 50 mm bore drive.
This 50 mm bore cylinder provides 982 N push at 0.5 MPa. If your application requires less force, the 40 mm neighbour offers 628 N push, whereas stepping up to the 63 mm bore yields 1559 N push. Because the stroke is 550 mm, the extended 20 mm rod and bearing face bending stresses under side loads; always support the load with an external guide to prevent premature seal wear. As a true ISO 15552 profile cylinder, it serves as a direct replacement for any standard 50 mm bore, 550 mm stroke unit with PT1/4 ports and your chosen mounting accessory.
Note that a plain SE cylinder does not hold its position or load when air pressure is lost or the valve is centred—the piston will drift. If your machine requires static holding without live pressure, consider the BSE rod lock variant or an external pilot-operated check valve.
AirtacDistr lists every SE50 order code with its price on one page at https://airtacdistr.com/products/airtac-se50-iso-air-cylinder
Quick checklist
At 0.5 MPa, this 50 mm bore cylinder provides 982 N of push force and 825 N of pull force. At 0.7 MPa, the push force increases to 1374 N. The maximum push force is 200 kgf when operated at the 1.0 MPa pressure limit.
Yes. The SE50X550S is dimensionally interchangeable per ISO 15552. You can drop it into existing 50 mm bore, 550 mm stroke setups using standard mounting hardware, provided the PT1/4 porting and 20 mm rod thread match your configuration.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.