
The AirTAC SE50 Standard Cylinder SE50X550SFA is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø50mm bore and 550mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE50X550SFA is a double-acting single-rod profile cylinder built to ISO 15552 standards, delivering a robust 982 N push force at 0.5 MPa alongside 1374 N at 0.7 MPa. Driven by a 50 mm bore and a 550 mm stroke, it integrates an FA front flange for rigid face-mounting and a built-in position-sensing magnet. The extruded aluminum barrel omits external tie rods entirely, yielding a flush exterior that simplifies machine integration and naturally resists corrosion.
This model features field-adjustable pneumatic cushioning at both stroke ends, allowing technicians to tune end-of-travel deceleration via a set screw to prevent hard mechanical impacts. The integrated magnet interfaces directly with AirTAC CMSE reed and DMSE electronic sensors, which slide neatly into the three sensor grooves machined into the barrel profile.
| Model | Airtac SE50 Standard Cylinder SE50X550SFA |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø50 mm |
| Stroke | 550 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 982 N | 825 N |
| 0.7 MPa | 1374 N | — |
| Max (@1.0 MPa) | 200 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 50 | Bore size in mm. |
| ×550 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Actuates a routing flap on a packaging conveyor, utilizing the 550 mm stroke and 982 N push to redirect heavy corrugated boxes between sorting lanes.
Opens and closes a sliding safety enclosure on a CNC turning center, relying on the FA flange for rigid mounting and the magnet for door-locked position confirmation.
Pushes layered product onto a wooden pallet within an automated stretch-wrap station, using the extended stroke length to reach across the pallet width.
Selecting this 50 mm bore makes sense when your application requires the 982 N push at 0.5 MPa that this cylinder provides. If your load demands less force, stepping down to the 40 mm bore yields 628 N of push, while stepping up to the 63 mm bore provides 1559 N for heavier payloads. Because this model carries the -S magnet code, it is fully primed for CMSE or DMSE position detection. The FA front flange supplies a solid mounting face for axial loads, and the PT1/4 port matches the standard 50 mm bore specification.
With a 550 mm stroke, the internal rod bearing experiences increased bending moments under side loading, so utilizing an external guide rail is highly recommended to prevent premature seal wear. Remember that the adjustable air cushion only decelerates the piston near the end of its travel; it does not lock the rod. If your process requires holding a load vertically without constant air pressure, you must incorporate an external pilot-operated check valve or transition to a BSE rod-lock variant.
AirtacDistr lists every SE50 order code with its price on one page at https://airtacdistr.com/products/airtac-se50-iso-air-cylinder
Quick checklist
At 0.5 MPa, this 50 mm bore cylinder provides 982 N of push force and 825 N of pull force. At 0.7 MPa, the push force increases to 1374 N, and the maximum push capacity is 200 kgf at 1.0 MPa. The operational speed range is 30-800 mm/s.
Yes, the SE50X550SFA is dimensionally interchangeable per ISO 15552, meaning it shares the exact same mounting footprint and interface dimensions as other ISO 15552 profile cylinders. You can swap it in using your existing FA front flange hardware and PT1/4 pneumatic connections.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.