Airtac SE50 Standard Cylinder SE50X560S
The AirTAC Airtac SE50 Standard Cylinder SE50X560S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø50mm bore and 560mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
- BoreØ50 mm
- Stroke560 mm
- Port sizePT1/4
- Acting typeDouble acting
- Rod threadM16×1.5
- CushionAdjustable, 30 mm
About the Airtac SE50 Standard Cylinder SE50X560S
The AirTAC SE50X560S is a double-acting, single-rod ISO 15552 profile cylinder engineered for demanding pneumatic tasks. It generates 982 N of push force at 0.5 MPa and features a 560 mm stroke. The extruded aluminum barrel omits external tie rods, yielding a compact, corrosion-resistant body that mounts flush against machine frames while protecting internal mechanics from washdown debris.
Equipped with a built-in magnet (-S), this unit seamlessly integrates with AirTAC CMSE reed and DMSE electronic sensors for precise end-of-stroke detection. Field-adjustable air cushions at both ends allow technicians to tune deceleration via a set screw, softening hard end stops during high-velocity 30-800 mm/s cycles to extend mechanical service life.
Airtac SE50 Standard Cylinder SE50X560S Technical Specifications
| Model | Airtac SE50 Standard Cylinder SE50X560S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø50 mm |
| Stroke | 560 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
Theoretical Output Force (Ø50mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 982 N | 825 N |
| 0.7 MPa | 1374 N | — |
| Max (@1.0 MPa) | 200 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SE50 Standard Cylinder SE50X560S
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 50 | Bore size in mm. |
| ×560 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Where the Airtac SE50 Standard Cylinder SE50X560S Is Used
Bottling Line Diverters
Ideal for routing plastic bottles on high-speed packaging conveyors, utilizing the 560 mm stroke to shift product lanes while the 982 N push force easily overcomes guide friction.
Palletizing Stop Gates
Provides robust stopping power for heavy pallet infeed sections, where the adjustable cushion smoothly decelerates the 50 mm bore at the end of its 560 mm travel.
Lab Test Fixture Clamping
Secures delicate housings for pressure decay testing, using the integrated magnet to trigger DMSE electronic sensors for precise clamping position verification.
Is the Airtac SE50 Standard Cylinder SE50X560S the Right Cylinder?
When sizing this 50 mm bore, note the 40 mm bore yields 628 N push at 0.5 MPa, while the 63 mm bore provides 1559 N. If your load requires intermediate force, this model strikes an optimal balance. Because the 560 mm stroke exceeds 300 mm, the unsupported piston rod is highly susceptible to bending under lateral loads; always pair this cylinder with an external guide rail to prevent premature rod-bearing wear.
As a dimensionally interchangeable ISO 15552 component, it serves as a drop-in replacement for other standard profile cylinders. To retrofit, match the 50 mm bore, 560 mm stroke, PT1/4 port, and your required mounting accessory. Remember that a standard SE cylinder drifts when air is lost; if the application must hold a load safely without live pressure, specify a BSE rod lock variant instead.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for CMSE/DMSE sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
- check Installation by qualified personnel per AirTAC docs.
Airtac SE50 Standard Cylinder SE50X560S FAQ
The SE50X560S generates 982 N push and 825 N pull at 0.5 MPa, 1374 N push at 0.7 MPa, and reaches a maximum push of 200 kgf at 1.0 MPa operating pressure.
No, the adjustable air cushion only decelerates the piston near the stroke end and does not function as a brake. If you need to hold a vertical load without continuous air pressure, use an AirTAC BSE series rod lock cylinder or an external pilot-operated check valve.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SE50 Standard Cylinder SE50X560S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.