Airtac SE50 Standard Cylinder SE50X600SN
The AirTAC Airtac SE50 Standard Cylinder SE50X600SN is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø50mm bore and 600mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
- BoreØ50 mm
- Stroke600 mm
- Port sizePT1/4
- Acting typeDouble acting
- Rod threadM16×1.5
- CushionAdjustable, 30 mm
About the Airtac SE50 Standard Cylinder SE50X600SN
The AirTAC SE50X600SN is a double-acting single-rod ISO 15552 profile cylinder engineered to deliver 982 N of push force at 0.5 MPa over a 600 mm stroke. Its square extruded aluminum barrel omits external tie rods, yielding a compact, corrosion-resistant body that mounts flush against machine frames while exposing the standardized ISO 15552 interface for immediate retrofitting.
This 50 mm bore unit integrates a built-in magnet for non-contact position sensing via AirTAC CMSE reed or DMSE electronic switches, paired with NBR seals for standard pneumatic duty. Field-adjustable air cushions at both ends allow you to dial in end-of-stroke deceleration, protecting payloads from hard impacts during high-speed traversal.
Airtac SE50 Standard Cylinder SE50X600SN Technical Specifications
| Model | Airtac SE50 Standard Cylinder SE50X600SN |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø50 mm |
| Stroke | 600 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
Theoretical Output Force (Ø50mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 982 N | 825 N |
| 0.7 MPa | 1374 N | — |
| Max (@1.0 MPa) | 200 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SE50 Standard Cylinder SE50X600SN
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 50 | Bore size in mm. |
| ×600 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Where the Airtac SE50 Standard Cylinder SE50X600SN Is Used
Pallet Conveyor Diverting
Actuates a diverting arm on a 982 N pallet handling line, using its 600 mm stroke to push heavy product loads cleanly between parallel conveyor belts.
Case Pack Forming
Drives the folding mechanism on a corrugated case packer, where the 825 N retract force at 0.5 MPa securely tucks flaps before sealing at high cyclic rates.
Textile Testing Fixture
Stretches fabric samples in a tensile testing fixture, relying on the adjustable end cushions to bring the 600 mm stroke to a smooth, impact-free stop.
Is the Airtac SE50 Standard Cylinder SE50X600SN the Right Cylinder?
Choosing this 50 mm bore cylinder means balancing a 982 N push at 0.5 MPa against your actual load requirements. If your application demands less force, stepping down to the 40 mm bore drops the output to 628 N, whereas upgrading to the 63 mm bore increases the push to 1559 N. Because the 600 mm stroke pushes the limits of the 50 mm series, the 20 mm rod and its M16x1.5 thread will experience significant bending moments under heavy lateral loads—an external guide rail is strongly recommended to prevent rod-bearing wear.
For ISO 15552 drop-in replacement, match the 50 mm bore, 600 mm stroke, PT1/4 port, and your specific mounting accessory. Note that the NBR seals and standard air cushions only decelerate the piston near stroke end; this cylinder cannot hold a load if air pressure drops. For position-holding safety, consider the BSE rod-lock variant.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for CMSE/DMSE sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
- check Installation by qualified personnel per AirTAC docs.
Airtac SE50 Standard Cylinder SE50X600SN FAQ
This 50 mm bore cylinder provides 982 N push and 825 N pull at 0.5 MPa, 1374 N push at 0.7 MPa, and a maximum push of 200 kgf at 1.0 MPa. It operates at speeds ranging from 30 to 800 mm/s.
Yes, the SE50X600SN is dimensionally interchangeable per ISO 15552 standards, matching the 50 mm bore, 600 mm stroke, PT1/4 port, and standard mounting footprints. It also features a built-in magnet compatible with AirTAC CMSE and DMSE sensors.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SE50 Standard Cylinder SE50X600SN
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.