verified AirTAC China Authorized Export Seller shield 100% Genuine AirTAC Parts workspace_premium 1-Year Warranty
appsShop by Modelexpand_more
person shopping_cart Request a QuoteQuote
AirTAC SE Series · ISO 15552 Cylinder

Airtac SE50 Standard Cylinder SE50X640S

The AirTAC SE50 Standard Cylinder SE50X640S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø50mm bore and 640mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.

  • BoreØ50 mm
  • Stroke640 mm
  • Port sizePT1/4
  • Acting typeDouble acting
  • Rod threadM16×1.5
  • CushionAdjustable, 30 mm
$149.31 $156.81Save 4% Standard model — usually dispatched in 3-5 days
Request a Quote
  • No minimum order. A single piece can be ordered.
  • Shipped from our own warehouse: most standard models dispatch in 3–5 days; custom and non-standard models take 8–10 business days. Transit time after that depends on the destination.
Compare every SE50 stroke, mounting and version on one page All SE50 codes →
verified Genuine AirTAC workspace_premium 1-year warranty bolt Reply in 7 h

About the Airtac SE50 Standard Cylinder SE50X640S

The AirTAC SE50X640S is a double-acting single-rod ISO 15552 profile cylinder engineered for a 640 mm stroke. It delivers 982 N of push force and 825 N of pull force at 0.5 MPa, making it well-suited for moderate-load linear actuation. The square extruded aluminum barrel omits external tie rods, yielding a compact, corrosion-resistant body that mounts flush into tight machine envelopes.

Equipped with a built-in magnet (-S), this unit supports AirTAC CMSE reed and DMSE electronic sensors for precise end-of-stroke detection. Field-adjustable pneumatic cushioning at both ends allows you to tune the deceleration of the piston via a set screw, softening hard impacts when cycling at high speeds. Because the 640 mm stroke exceeds the standard 1200 mm maximum for this bore, it is manufactured as a non-standard made-to-order configuration.

Airtac SE50 Standard Cylinder SE50X640S Technical Specifications

ModelAirtac SE50 Standard Cylinder SE50X640S
SeriesSE ISO 15552 profile cylinder
Bore sizeØ50 mm
Stroke640 mm
Acting typeDouble acting
Port sizePT1/4
Rod threadM16×1.5
FluidAir (filtered by 40µm element)
Operating pressure0.15 – 1.0 MPa
Proof pressure1.5 MPa
Temperature-20 to +70 °C (0–150 °C with FKM seals)
Speed range30 – 800 mm/s
CushionAdjustable, 30 mm
Max strokeUp to 1200 mm

Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).

Theoretical Output Force (Ø50mm)

PressurePush forcePull force
0.5 MPa982 N825 N
0.7 MPa1374 N—
Max (@1.0 MPa)200 kgf

Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.

Model Code: Airtac SE50 Standard Cylinder SE50X640S

SEISO 15552 / VDMA 24562 profile-barrel double-acting cylinder.
50Bore size in mm.
×640Stroke length in mm.
-SOptional built-in magnet for CMSE / DMSE sensor sensing.

Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).

Where the Airtac SE50 Standard Cylinder SE50X640S Is Used

conveyor_belt

Pallet Diverting Gate

Actuates a routing flap on a packaging conveyor, using the 640 mm stroke to redirect heavy pallets with 982 N of push force at 0.5 MPa.

straighten

Long-Stroke Sheet Stacker

Pushes cut metal sheets into a stacking magazine, where the field-adjustable air cushion smoothly decelerates the load to prevent denting at the end of the 640 mm travel.

warehouse

Automated Storage Retriever

Extends a retrieval arm deep into a dense storage rack, relying on the built-in magnet and DMSE electronic sensors to confirm the fully extended position.

Is the Airtac SE50 Standard Cylinder SE50X640S the Right Cylinder?

This 50 mm bore generates 982 N push at 0.5 MPa. If your application requires less force, the 40 mm bore offers 628 N push, while stepping up to the 63 mm bore provides 1559 N push for heavier payloads. As a standard ISO 15552 cylinder, it serves as a direct dimensional replacement for other ISO 15552 cylinders, sharing standardized mounting hardware like FA front flanges or LB foot brackets. The port size is PT1/4, and the rod-end thread is M16x1.5.

Because the 640 mm stroke is non-standard and creates a long unsupported rod extension, you must account for rod-bearing bending under side loads; fitting an external guide rail is strongly recommended to prevent premature seal wear. Remember that a standard SE cylinder does not hold its position when air is removed or a valve is centered, as the piston will drift; if your machine requires true static load holding without live pressure, consider the BSE rod-lock variant or an external pilot-operated check valve.

AirtacDistr lists every SE50 order code with its price on one page at https://airtacdistr.com/products/airtac-se50-iso-air-cylinder

Quick checklist

  • ✓ Required force at your working pressure
  • ✓ Stroke and mounting space
  • ✓ Port/thread type (PT/G)
  • ✓ Magnet (-S) for CMSE/DMSE sensors?
  • ✓ Side load — consider a guided cylinder
Ask an Engineer

Installation & Maintenance Notes

  • check Use clean air filtered to 40µm or finer.
  • check Keep within 0.15 – 1.0 MPa operating pressure.
  • check Avoid side load on the piston rod.
  • check Adjust end cushion screws for smooth stops.
  • check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
  • check Installation by qualified personnel per AirTAC docs.

Airtac SE50 Standard Cylinder SE50X640S FAQ

The SE50X640S provides 982 N push and 825 N pull at 0.5 MPa, 1374 N push at 0.7 MPa, and a maximum push of 200 kgf at 1.0 MPa. The 640 mm stroke is a non-standard made-to-order length that exceeds the standard 1200 mm maximum for a 50 mm bore.

Yes, the SE50X640S shares the standardized ISO 15552 mounting interface, making it dimensionally interchangeable with other ISO 15552 profile cylinders. It uses a PT1/4 port and includes a built-in magnet compatible with AirTAC CMSE and DMSE sensors.

verified

Authorized Export Seller

Genuine AirTAC parts produced by AirTAC factory.

workspace_premium

1-Year Warranty

Covers non-human-caused product damage.

local_shipping

Fast Dispatch

Most standard models are dispatched in 3-5 days.

bolt

Fast Reply

Most inquiries answered within 7 hours.

Related AirTAC SE Cylinders

Request a Quote for Airtac SE50 Standard Cylinder SE50X640S

Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.

Thank you. We received your request for SE50X640S and will confirm price, availability and lead time — usually within 7 hours.

For the fastest response, keep the complete model number above and include a clear photo of the product label. If photo upload is unavailable, email photos to [email protected] with your model number.