Airtac SE50 Standard Cylinder SE50X730S
The AirTAC Airtac SE50 Standard Cylinder SE50X730S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø50mm bore and 730mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
- BoreØ50 mm
- Stroke730 mm
- Port sizePT1/4
- Acting typeDouble acting
- Rod threadM16×1.5
- CushionAdjustable, 30 mm
About the Airtac SE50 Standard Cylinder SE50X730S
The AirTAC SE50X730S is a double-acting, single-rod ISO 15552 profile cylinder engineered to deliver 982 N of push force at 0.5 MPa across a 730 mm stroke. Its extruded aluminum barrel omits external tie rods, yielding a compact, corrosion-resistant body that mounts flush against machine frames while protecting internal components from harsh environments.
Equipped with a built-in magnet (-S), this unit seamlessly integrates with AirTAC CMSE reed and DMSE electronic sensors for precise end-of-trroke detection. The field-adjustable pneumatic cushioning at both ends allows technicians to dial in end-cap deceleration, softening hard mechanical stops during high-velocity 30-800 mm/s cycling.
Airtac SE50 Standard Cylinder SE50X730S Technical Specifications
| Model | Airtac SE50 Standard Cylinder SE50X730S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø50 mm |
| Stroke | 730 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
Theoretical Output Force (Ø50mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 982 N | 825 N |
| 0.7 MPa | 1374 N | — |
| Max (@1.0 MPa) | 200 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SE50 Standard Cylinder SE50X730S
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 50 | Bore size in mm. |
| ×730 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Where the Airtac SE50 Standard Cylinder SE50X730S Is Used
Pallet Transfer Line Diverter
Uses the 982 N push force at 0.5 MPa to deflect heavy timber pallets onto a side spur, with the 730 mm stroke ensuring full extension across the conveyor width.
Corrugated Box Flap Folder
Cycles at 30-800 mm/s to rapidly fold large cardboard flaps, relying on the adjustable end cushions to prevent destructive impact at the 730 mm stroke limit.
Industrial Parts Wash Station
Lowers heavy metal baskets into a solvent tank, using the -S magnet and DMSE electronic sensors to verify the 50 mm bore cylinder has reached full submersion depth.
Is the Airtac SE50 Standard Cylinder SE50X730S the Right Cylinder?
This 50 mm bore provides 982 N push at 0.5 MPa; if your load is lighter, the 40 mm bore offers 628 N, while heavier payloads require the 63 mm bore with 1559 N. Because the 730 mm stroke is substantial, the 20 mm rod and bearing are subject to bending under side loads—always incorporate an external guide rail to prevent premature wear. As a true ISO 15552 profile cylinder, it serves as a drop-in replacement for any standard 50 mm bore with PT1/4 ports and 200 mm stroke, sharing standardized mounting hardware. Note that a plain SE cylinder drifts when air is lost; use a BSE rod lock for strict position holding.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for CMSE/DMSE sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
- check Installation by qualified personnel per AirTAC docs.
Airtac SE50 Standard Cylinder SE50X730S FAQ
The 50 mm bore generates 982 N push and 825 N pull at 0.5 MPa. At 0.7 MPa, the push force is 1374 N, and the maximum push force is 200 kgf at 1.0 MPa.
No. The adjustable air cushion at both ends only decelerates the piston near the stroke end; it does not lock or hold the load. If air is lost, the cylinder will drift. For position holding, use a BSE rod lock variant.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SE50 Standard Cylinder SE50X730S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.