verified AirTAC China Authorized Export Seller shield 100% Genuine AirTAC Parts workspace_premium 1-Year Warranty
appsShop by Modelexpand_more
person shopping_cart Request a QuoteQuote
AirTAC SE Series · ISO 15552 Cylinder

Airtac SE63 Standard Cylinder SE63X1040S

The AirTAC SE63 Standard Cylinder SE63X1040S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø63mm bore and 1040mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.

  • BoreØ63 mm
  • Stroke1040 mm
  • Port sizePT3/8
  • Acting typeDouble acting
  • Rod threadM16×1.5
  • CushionAdjustable, 36 mm
$240.30 $247.80Save 3% Standard model — usually dispatched in 3-5 days
Request a Quote
  • No minimum order. A single piece can be ordered.
  • Shipped from our own warehouse: most standard models dispatch in 3–5 days; custom and non-standard models take 8–10 business days. Transit time after that depends on the destination.
Compare every SE63 stroke, mounting and version on one page All SE63 codes →
verified Genuine AirTAC workspace_premium 1-year warranty bolt Reply in 7 h

About the Airtac SE63 Standard Cylinder SE63X1040S

The AirTAC SE63X1040S is a double-acting, single-rod ISO 15552 profile cylinder engineered for demanding linear motion tasks. Operating at 0.15-1.0 MPa, this 63 mm bore unit generates a push force of 1559 N and a pull force of 1402 N at 0.5 MPa. Its square extruded aluminum barrel lacks external tie rods, yielding a compact, corrosion-resistant body that mounts flush against machine frames while leaving the integrated sensor grooves fully accessible.

This specific configuration includes a 1040 mm stroke, which exceeds the 1500 mm standard maximum for this bore, making it a made-to-order unit. It features a built-in magnet (-S) for seamless integration with AirTAC CMSE reed and DMSE electronic position sensors. The field-adjustable pneumatic cushioning at both ends allows technicians to tune end-of-stroke deceleration via a set screw, softening hard impacts during high-speed 30-800 mm/s cycling.

Airtac SE63 Standard Cylinder SE63X1040S Technical Specifications

ModelAirtac SE63 Standard Cylinder SE63X1040S
SeriesSE ISO 15552 profile cylinder
Bore sizeØ63 mm
Stroke1040 mm
Acting typeDouble acting
Port sizePT3/8
Rod threadM16×1.5
FluidAir (filtered by 40µm element)
Operating pressure0.15 – 1.0 MPa
Proof pressure1.5 MPa
Temperature-20 to +70 °C (0–150 °C with FKM seals)
Speed range30 – 800 mm/s
CushionAdjustable, 36 mm
Max strokeUp to 1500 mm

Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).

Theoretical Output Force (Ø63mm)

PressurePush forcePull force
0.5 MPa1559 N1402 N
0.7 MPa2182 N—
Max (@1.0 MPa)318 kgf

Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.

Model Code: Airtac SE63 Standard Cylinder SE63X1040S

SEISO 15552 / VDMA 24562 profile-barrel double-acting cylinder.
63Bore size in mm.
×1040Stroke length in mm.
-SOptional built-in magnet for CMSE / DMSE sensor sensing.

Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).

Where the Airtac SE63 Standard Cylinder SE63X1040S Is Used

conveyor_belt

Bottling Line Diversion

Actuates diverter gates on high-speed beverage conveyor lines, using the 1559 N push force to reliably pivot heavy guide arms and redirect glass bottles between packaging lanes.

packaging

Palletizer Top Platten

Drives the top platen mechanism on automated palletizing cells, securing unstable pallet loads during stretch-wrapping cycles with its 1040 mm extended reach.

science

Textile Tenter Frame

Manages fabric edge-guide tensioning on wide textile tenter frames, where the magnetic piston enables CMSE sensors to confirm precise fabric positioning over long strokes.

Is the Airtac SE63 Standard Cylinder SE63X1040S the Right Cylinder?

Delivering 1559 N push at 0.5 MPa, this 63 mm bore fits perfectly between the smaller 50 mm bore (982 N push) and the larger 80 mm bore (2513 N push) if you need to step up or down for load adjustments. Because this is a 1040 mm stroke, the unsupported piston rod is highly susceptible to bending under side loads; utilizing an external guide rail is strongly recommended to prevent premature rod-bearing wear.

As a dimensionally interchangeable ISO 15552 cylinder, it serves as a direct replacement for other standard profile cylinders without altering mounting patterns. It uses a PT3/8 port and an M16x1.5 rod thread. Note that the adjustable air cushion only decelerates the piston near stroke end; it does not hold a load. If the application requires position holding upon air loss, consider the BSE rod lock variant.

AirtacDistr lists every SE63 order code with its price on one page at https://airtacdistr.com/products/airtac-se63-iso-air-cylinder

Quick checklist

  • ✓ Required force at your working pressure
  • ✓ Stroke and mounting space
  • ✓ Port/thread type (PT/G)
  • ✓ Magnet (-S) for CMSE/DMSE sensors?
  • ✓ Side load — consider a guided cylinder
Ask an Engineer

Installation & Maintenance Notes

  • check Use clean air filtered to 40µm or finer.
  • check Keep within 0.15 – 1.0 MPa operating pressure.
  • check Avoid side load on the piston rod.
  • check Adjust end cushion screws for smooth stops.
  • check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
  • check Installation by qualified personnel per AirTAC docs.

Airtac SE63 Standard Cylinder SE63X1040S FAQ

At 0.5 MPa, the 63 mm bore provides a push force of 1559 N and a pull force of 1402 N. At 0.7 MPa, the push force is 2182 N. The maximum allowable push force is 318 kgf at 1.0 MPa.

Yes, the SE63X1040S is dimensionally interchangeable per ISO 15552 standards. You can drop it into existing foot or flange mounting patterns and use standard PT3/8 pneumatic connections without modifying the machine frame.

verified

Authorized Export Seller

Genuine AirTAC parts produced by AirTAC factory.

workspace_premium

1-Year Warranty

Covers non-human-caused product damage.

local_shipping

Fast Dispatch

Most standard models are dispatched in 3-5 days.

bolt

Fast Reply

Most inquiries answered within 7 hours.

Related AirTAC SE Cylinders

Request a Quote for Airtac SE63 Standard Cylinder SE63X1040S

Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.

Thank you. We received your request for SE63X1040S and will confirm price, availability and lead time — usually within 7 hours.

For the fastest response, keep the complete model number above and include a clear photo of the product label. If photo upload is unavailable, email photos to [email protected] with your model number.