
The AirTAC SE63 Standard Cylinder SE63X1050S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø63mm bore and 1050mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE63X1050S is a double-acting, single-rod ISO 15552 profile cylinder engineered for a 1050 mm stroke, delivering a robust 1559 N push force at 0.5 MPa. Because this stroke exceeds the 1500 mm standard maximum for this bore, it is supplied as a made-to-order unit for specialized long-traverse tasks. The integrated -S magnet enables direct fitment of CMSE reed and DMSE electronic sensors for precise end-position detection.
Its extruded aluminum barrel omits external tie rods, yielding a compact, corrosion-resistant body that mounts flush against machine frames. Field-adjustable pneumatic cushioning at both ends allows technicians to tune end-stop deceleration via a set screw, softening impacts during high-speed traversal. The Ø20 mm hard-chrome rod and PT3/8 port ensure reliable force transmission and airflow for heavy-duty cycles.
| Model | Airtac SE63 Standard Cylinder SE63X1050S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø63 mm |
| Stroke | 1050 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 1559 N | 1402 N |
| 0.7 MPa | 2182 N | — |
| Max (@1.0 MPa) | 318 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 63 | Bore size in mm. |
| ×1050 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Uses the 1050 mm stroke to push heavy pallets sideways between adjacent roller lines, utilizing the 1559 N push force to overcome friction without stalling.
Drives a vertical lifting gantry in automated small-parts warehouses, where the built-in -S magnet and DMSE sensors confirm exact shelf-level positioning.
Extracts formed metal deep-draw parts from hydraulic presses, relying on the adjustable end cushions to soften the 30-800 mm/s travel deceleration at full extension.
This 63 mm bore yields 1559 N push at 0.5 MPa. If your load requires less force, the 50 mm bore offers 982 N push; if you need substantially more thrust, stepping up to the 80 mm bore provides 2513 N push. Because the 1050 mm stroke is non-standard, expect a made-to-order lead time. A standard SE does not hold a load if air pressure is lost or the valve centers; the piston will drift. For fail-safe position holding, pair this cylinder with a BSE rod lock or an external pilot-operated check valve.
At 1050 mm of unsupported stroke, the bending moment on the rod bearing increases significantly under side loads. To prevent premature seal wear and binding, guide the load externally using linear rails rather than relying on the cylinder rod alone. The -S magnet works seamlessly with AirTAC CMSE and DMSE switches for direct ISO 15552 machine retrofits.
AirtacDistr lists every SE63 order code with its price on one page at https://airtacdistr.com/products/airtac-se63-iso-air-cylinder
Quick checklist
At 0.5 MPa, this 63 mm bore cylinder provides 1559 N of push force and 1402 N of pull force. At 0.7 MPa, the push force increases to 2182 N, with a maximum push capacity of 318 kgf at 1.0 MPa. It operates at speeds of 30-800 mm/s.
No, the adjustable air cushion only decelerates the piston near the stroke ends and does not lock the rod. If air is lost, the piston will drift. For position holding, you must use a BSE series rod lock or an external mechanical brake.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.