
The AirTAC SE63 Standard Cylinder SE63X1160S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø63mm bore and 1160mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE63X1160S is a double-acting single-rod ISO 15552 profile cylinder engineered for extended travel. It delivers a robust 1559 N push at 0.5 MPa, utilizing a 63 mm bore and a 1160 mm stroke to bridge the gap between standard lengths and custom automation requirements.
This unit features a square extruded aluminum barrel without external tie rods, creating a compact and corrosion-resistant body that mounts flush against machine frames. Equipped with a built-in magnet, it seamlessly integrates with AirTAC CMSE reed and DMSE electronic sensors for precise end-position detection.
| Model | Airtac SE63 Standard Cylinder SE63X1160S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø63 mm |
| Stroke | 1160 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 1559 N | 1402 N |
| 0.7 MPa | 2182 N | — |
| Max (@1.0 MPa) | 318 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 63 | Bore size in mm. |
| ×1160 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Drives the extended push-off stroke on a 63 mm bore pallet transfer system, using its 1559 N force to index heavy goods between machining centers.
Actuates a long-travel vertical lift gate in a high-bay warehouse, relying on the 1160 mm stroke to clear the overhead passageway for forklift access.
Ejects large diameter packaging film rolls from a winder, utilizing the built-in magnet and DMSE sensors to confirm full 1160 mm extension.
This 63 mm bore strikes a balance between the smaller 50 mm option (982 N push at 0.5 MPa) and the larger 80 mm class (2513 N push at 0.5 MPa), allowing you to step up or down depending on your payload. Because the 1160 mm stroke exceeds the standard maximum of 1500 mm, it is processed as a non-standard made-to-order configuration. At this extended length, the 20 mm piston rod is highly susceptible to side-load bending; an external guide rail is strongly recommended to prevent premature rod-bearing wear. As a true ISO 15552 profile cylinder, it serves as a direct replacement for any standard 63 mm bore with a PT3/8 port and your chosen mounting accessory. Note that the adjustable air cushions at both ends only decelerate the piston near stroke end—they do not hold the load if air pressure is lost.
AirtacDistr lists every SE63 order code with its price on one page at https://airtacdistr.com/products/airtac-se63-iso-air-cylinder
Quick checklist
At 0.5 MPa, the push force is 1559 N and the pull force is 1402 N. At 0.7 MPa, the push force increases to 2182 N. The maximum push force is 318 kgf at 1.0 MPa. The operating pressure range is 0.15-1.0 MPa, and the operational speed is 30-800 mm/s.
Yes, the SE63X1160S is dimensionally interchangeable per ISO 15552 / VDMA 24562. You can drop it into existing 63 mm bore footprints using standard mounting hardware and the PT3/8 port without modifying the machine frame.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.