
The AirTAC SE63 Standard Cylinder SE63X132S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø63mm bore and 132mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE63X132S is a double-acting single-rod profile cylinder operating at 0.15-1.0 MPa, delivering a robust 1559 N push force at 0.5 MPa. Built to the ISO 15552 / VDMA 24562 standard, its extruded aluminum barrel omits external tie rods, yielding a compact, corrosion-resistant body that mounts flush in tight machine envelopes.
This 132 mm stroke unit includes a built-in magnet (-S) for direct integration with AirTAC CMSE reed and DMSE electronic sensors across its three-side sensor grooves. The field-adjustable air cushioning at both ends allows precise tuning of end-of-stroke deceleration, protecting payloads from hard mechanical impacts.
| Model | Airtac SE63 Standard Cylinder SE63X132S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø63 mm |
| Stroke | 132 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 1559 N | 1402 N |
| 0.7 MPa | 2182 N | — |
| Max (@1.0 MPa) | 318 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 63 | Bore size in mm. |
| ×132 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Provides the 1559 N push at 0.5 MPa required to snap corrugated carton blanks into shape, utilizing the 132 mm stroke to clear the packaging mechanism during retraction.
Drives small mold ejector pins with precise 132 mm travel, relying on the adjustable end cushions to prevent damage to delicate molded plastic components at high cycle speeds.
Actuates a routing arm on a 63 mm bore line, using the built-in magnet to trigger DMSE solid-state sensors for confirming load diversion positions.
If 1559 N of thrust is excessive for your payload, the 50 mm bore offers 982 N push at 0.5 MPa; conversely, stepping up to the 80 mm bore yields 2513 N for heavier demands. Because this is a 132 mm stroke, side-loading remains moderate, but always verify the rod-end thread M16x1.5 alignment to prevent premature seal wear.
As a dimensionally interchangeable ISO 15552 cylinder, it serves as a direct replacement for other standard profile cylinders, sharing standardized mounting accessories. Note that the adjustable air cushion only decelerates the piston near stroke end; it does not lock or hold the load if air pressure is lost. For position holding, consider the BSE rod lock variant.
AirtacDistr lists every SE63 order code with its price on one page at https://airtacdistr.com/products/airtac-se63-iso-air-cylinder
Quick checklist
At 0.5 MPa, the SE63X132S delivers 1559 N push and 1402 N pull. At 0.7 MPa, the push force is 2182 N, with a maximum push of 318 kgf at 1.0 MPa. It features a 63 mm bore, 132 mm stroke, PT3/8 port, and a Ø20 mm rod with an M16x1.5 thread.
Yes, the SE63X132S is dimensionally interchangeable per ISO 15552, meaning it shares the exact mounting footprint and can serve as a direct replacement for other ISO 15552 profile cylinders using standard mounting hardware.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.