
The AirTAC SE63 Standard Cylinder SE63X1350S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø63mm bore and 1350mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE63X1350S is a double-acting, single-rod ISO 15552 profile cylinder engineered for long-stroke actuation. It provides 1559 N of push force and 1402 N of pull force at 0.5 MPa, utilizing a 63 mm bore and a 1350 mm non-standard stroke. The extruded aluminum barrel omits external tie rods, yielding a compact, corrosion-resistant body that mounts flush against machine frames while resisting debris buildup.
Equipped with a built-in magnet (-S), this unit supports AirTAC CMSE reed and DMSE electronic position sensing. Field-adjustable pneumatic cushioning at both ends allows you to tune end-of-stroke deceleration, softening hard impacts when cycling at speeds up to 800 mm/s. The 36 mm cushion length and PT3/8 port ensure robust airflow for rapid pressurization.
| Model | Airtac SE63 Standard Cylinder SE63X1350S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø63 mm |
| Stroke | 1350 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 1559 N | 1402 N |
| 0.7 MPa | 2182 N | — |
| Max (@1.0 MPa) | 318 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 63 | Bore size in mm. |
| ×1350 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Drives the 1350 mm stroke to push heavy pallets between roller conveyor sections, utilizing the 1559 N push force to overcome friction without stalling.
Actuates a large-format packaging web guide over a 1350 mm span, using the built-in magnet with DMSE sensors to verify material feed position.
Lifts stacked components within a fabrication cell, relying on the field-adjustable cushioning to soften end-stops during rapid 800 mm/s vertical cycles.
This 63 mm bore generates 1559 N push at 0.5 MPa; stepping down to a 50 mm bore drops output to 982 N, while stepping up to an 80 mm bore raises it to 2513 N. Because this is a 1350 mm stroke, the unsupported piston rod is highly susceptible to bending under side loads—always incorporate an external guide rail to prevent rod-bearing damage. As a double-acting cylinder, it will drift if air pressure is lost; use a BSE rod lock for fail-safe load holding. This model is dimensionally interchangeable per ISO 15552, serving as a direct replacement for other ISO 15552 cylinders with matching 63 mm bore, 1350 mm stroke, PT3/8 port, and your chosen mounting accessory.
AirtacDistr lists every SE63 order code with its price on one page at https://airtacdistr.com/products/airtac-se63-iso-air-cylinder
Quick checklist
At 0.5 MPa, the 63 mm bore yields 1559 N push and 1402 N pull. At 0.7 MPa, push increases to 2182 N. The maximum push force is 318 kgf at 1.0 MPa. The 1350 mm stroke is classified as non-standard and made-to-order.
No, the adjustable air cushion only decelerates the piston near stroke end and does not act as a brake; the cylinder will drift without live pressure, requiring a BSE rod lock for holding. The built-in -S magnet is specifically designed to trigger AirTAC CMSE reed and DMSE electronic sensors for position detection.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.