
The AirTAC SE63 Standard Cylinder SE63X150SN is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø63mm bore and 150mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE63X150SN is a double-acting, single-rod ISO 15552 profile cylinder engineered to deliver a robust 1559 N push force at 0.5 MPa. Its square extruded aluminum barrel eliminates external tie rods, yielding a compact, corrosion-resistant body that mounts flush against machine frames while exposing standardized ISO 15552 interface dimensions for seamless retrofitting.
Equipped with an NBR seal, this 63 mm bore unit operates reliably across standard temperature ranges and integrates a built-in magnet for CMSE reed and DMSE electronic sensors. The field-adjustable air cushioning at both ends allows technicians to tune end-of-stroke deceleration, softening hard impacts during high-speed 30-800 mm/s cycles.
| Model | Airtac SE63 Standard Cylinder SE63X150SN |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø63 mm |
| Stroke | 150 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 1559 N | 1402 N |
| 0.7 MPa | 2182 N | — |
| Max (@1.0 MPa) | 318 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 63 | Bore size in mm. |
| ×150 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Provides the 1559 N push force required to smoothly fold and seal heavy corrugated cardboard flaps at 150 mm stroke without stalling.
Uses the 150 mm travel to push heavy pallets onto a branching conveyor line, benefiting from the adjustable cushion to halt the load gently.
Drives molded plastic parts out of a press cavity, leveraging the NBR seals and CMSE/DMSE magnet compatibility for reliable cycle counting.
Generating 1559 N of push at 0.5 MPa, this 63 mm bore sits perfectly between the 50 mm bore (982 N push) and the 80 mm bore (2513 N push), allowing you to step down for lighter duty or up for heavier loads. The 150 mm stroke provides ample travel, but note that a plain SE cylinder will drift and cannot hold a load if air pressure is lost—use a BSE rod lock variant for secure positioning. Because the stroke is 150 mm, the 20 mm piston rod and M16x1.5 thread handle standard side loads adequately, though long unsupported strokes over 300 mm would require an external guide. To upgrade an existing fixture, match the 63 mm bore, 150 mm stroke, PT3/8 port, and add an -S magnet for position sensing.
AirtacDistr lists every SE63 order code with its price on one page at https://airtacdistr.com/products/airtac-se63-iso-air-cylinder
Quick checklist
This 63 mm bore cylinder generates 1559 N push and 1402 N pull at 0.5 MPa, 2182 N push at 0.7 MPa, and a maximum push of 318 kgf at 1.0 MPa. The operating speed range is 30-800 mm/s.
Yes, the SE63X150SN is dimensionally interchangeable per ISO 15552 standards, meaning it shares identical mounting footprint and hole patterns with other ISO 15552 profile cylinders. You can drop it into existing hardware using the standard PT3/8 port and M16x1.5 rod thread.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.