verified AirTAC China Authorized Export Seller shield 100% Genuine AirTAC Parts workspace_premium 1-Year Warranty
appsShop by Modelexpand_more
person shopping_cart Request a QuoteQuote
AirTAC SE Series · ISO 15552 Cylinder

Airtac SE63 Standard Cylinder SE63X1550S

The AirTAC SE63 Standard Cylinder SE63X1550S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø63mm bore and 1550mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.

  • BoreØ63 mm
  • Stroke1550 mm
  • Port sizePT3/8
  • Acting typeDouble acting
  • Rod threadM16×1.5
  • CushionAdjustable, 36 mm
$327.52 $335.02Save 2% Standard model — usually dispatched in 3-5 days
Request a Quote
  • No minimum order. A single piece can be ordered.
  • Shipped from our own warehouse: most standard models dispatch in 3–5 days; custom and non-standard models take 8–10 business days. Transit time after that depends on the destination.
Compare every SE63 stroke, mounting and version on one page All SE63 codes →
verified Genuine AirTAC workspace_premium 1-year warranty bolt Reply in 7 h

About the Airtac SE63 Standard Cylinder SE63X1550S

The AirTAC SE63X1550S is a double-acting, single-rod ISO 15552 profile cylinder engineered for a non-standard 1550 mm stroke. It delivers a robust 1559 N push force at 0.5 MPa, utilizing a 20 mm rod and a PT3/8 port. Because this length exceeds the standard 1500 mm maximum, it is produced as a made-to-order unit for specialized long-reach machinery.

The extruded aluminum barrel design omits external tie rods, yielding a compact, corrosion-resistant body that mounts flush while exposing sensor grooves on three sides. Equipped with a built-in magnet (S), the cylinder supports AirTAC CMSE reed and DMSE electronic position switches for precise end-of-stroke detection. Field-adjustable air cushioning at both ends allows technicians to tune deceleration, softening the impact of heavy loads at high travel speeds.

Airtac SE63 Standard Cylinder SE63X1550S Technical Specifications

ModelAirtac SE63 Standard Cylinder SE63X1550S
SeriesSE ISO 15552 profile cylinder
Bore sizeØ63 mm
Stroke1550 mm
Acting typeDouble acting
Port sizePT3/8
Rod threadM16×1.5
FluidAir (filtered by 40µm element)
Operating pressure0.15 – 1.0 MPa
Proof pressure1.5 MPa
Temperature-20 to +70 °C (0–150 °C with FKM seals)
Speed range30 – 800 mm/s
CushionAdjustable, 36 mm
Max strokeUp to 1500 mm

Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).

Theoretical Output Force (Ø63mm)

PressurePush forcePull force
0.5 MPa1559 N1402 N
0.7 MPa2182 N—
Max (@1.0 MPa)318 kgf

Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.

Model Code: Airtac SE63 Standard Cylinder SE63X1550S

SEISO 15552 / VDMA 24562 profile-barrel double-acting cylinder.
63Bore size in mm.
×1550Stroke length in mm.
-SOptional built-in magnet for CMSE / DMSE sensor sensing.

Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).

Where the Airtac SE63 Standard Cylinder SE63X1550S Is Used

conveyor_belt

Automotive Skid Conveyor Transfer

Pushes heavy automotive skids between conveyor lines using its 1559 N push force and 1550 mm reach, with the -S magnet tracking transfer completion via DMSE sensors.

straighten

Long-Stroke Metal Panel Straightener

Flattens wide sheet metal panels in a press feed system where the 1550 mm stroke accommodates oversized material widths and the adjustable cushion softens rapid retraction.

warehouse

Palletizing Robot Feed Arm

Actuates a long horizontal feed arm in a palletizing cell, using the 318 kgf maximum thrust to index heavy pallets while relying on external guides to support the extended rod.

Is the Airtac SE63 Standard Cylinder SE63X1550S the Right Cylinder?

When sizing this actuator, stepping down to a 50 mm bore yields 982 N push at 0.5 MPa, while stepping up to an 80 mm bore provides 2513 N. This 63 mm model hits a versatile middle ground, generating 1559 N push and 1402 N pull at 0.5 MPa, with a maximum thrust of 318 kgf at 1.0 MPa. Because the 1550 mm stroke is non-standard and exceeds the 1500 mm catalog maximum, expect a made-to-order lead time.

At this extreme stroke length, the 20 mm piston rod is highly susceptible to side-load bending and rod-bearing wear; an external guide rail is strongly recommended to prevent premature seal failure. For direct retrofits, it shares the exact ISO 15552 mounting interface and PT3/8 port of comparable cylinders, and the -S magnet enables CMSE/DMSE sensor tracking. Note that the adjustable end cushions only decelerate the piston near stroke end; they cannot hold a load if air pressure drops, a function requiring a BSE rod lock.

AirtacDistr lists every SE63 order code with its price on one page at https://airtacdistr.com/products/airtac-se63-iso-air-cylinder

Quick checklist

  • ✓ Required force at your working pressure
  • ✓ Stroke and mounting space
  • ✓ Port/thread type (PT/G)
  • ✓ Magnet (-S) for CMSE/DMSE sensors?
  • ✓ Side load — consider a guided cylinder
Ask an Engineer

Installation & Maintenance Notes

  • check Use clean air filtered to 40µm or finer.
  • check Keep within 0.15 – 1.0 MPa operating pressure.
  • check Avoid side load on the piston rod.
  • check Adjust end cushion screws for smooth stops.
  • check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
  • check Installation by qualified personnel per AirTAC docs.

Airtac SE63 Standard Cylinder SE63X1550S FAQ

At 0.5 MPa, this 63 mm bore cylinder provides 1559 N push and 1402 N pull. At 0.7 MPa, the push force is 2182 N, and the maximum push is 318 kgf at 1.0 MPa. The operating speed ranges from 30-800 mm/s.

Yes, it shares the exact ISO 15552 / VDMA 24562 dimensional interface, allowing it to direct replace other standard profile cylinders using existing mounting hardware and PT3/8 ports. The 1550 mm stroke is non-standard and made-to-order.

verified

Authorized Export Seller

Genuine AirTAC parts produced by AirTAC factory.

workspace_premium

1-Year Warranty

Covers non-human-caused product damage.

local_shipping

Fast Dispatch

Most standard models are dispatched in 3-5 days.

bolt

Fast Reply

Most inquiries answered within 7 hours.

Related AirTAC SE Cylinders

Request a Quote for Airtac SE63 Standard Cylinder SE63X1550S

Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.

Thank you. We received your request for SE63X1550S and will confirm price, availability and lead time — usually within 7 hours.

For the fastest response, keep the complete model number above and include a clear photo of the product label. If photo upload is unavailable, email photos to [email protected] with your model number.