
The AirTAC SE63 Standard Cylinder SE63X15S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø63mm bore and 15mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE63X15S is a double-acting single-rod profile cylinder built to ISO 15552 dimensions, delivering a robust 1559 N push at 0.5 MPa within a compact 15 mm stroke. Its square extruded aluminum barrel omits external tie rods, yielding a flush, corrosion-resistant body that simplifies mounting in tight spaces.
Equipped with a built-in magnet, this unit directly supports AirTAC CMSE reed and DMSE electronic sensors for precise end-position detection. The field-adjustable air cushioning at both ends lets you fine-tune deceleration to soften hard mechanical impacts during rapid cycles.
| Model | Airtac SE63 Standard Cylinder SE63X15S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø63 mm |
| Stroke | 15 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 1559 N | 1402 N |
| 0.7 MPa | 2182 N | — |
| Max (@1.0 MPa) | 318 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 63 | Bore size in mm. |
| ×15 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Uses the 1559 N extend force to positively eject small stamped metal parts from a die within a tight 15 mm clearance window.
Rapidly folds corrugated carton flaps prior to sealing, relying on the adjustable end cushions to prevent tearing the cardboard.
Applies localized clamping pressure for bending thin sheet metal brackets, utilizing the 1402 N retract force to reset the tooling.
Choosing this 63 mm bore provides 1559 N push at 0.5 MPa. If your application requires less force, the 50 mm bore offers 982 N push; if you need more power, stepping up to the 80 mm bore yields 2513 N push. The PT3/8 port and M16x1.5 rod thread handle substantial side loads, though an external guide is always recommended for offset loads.
Because the stroke is only 15 mm, the internal rod bearing sees minimal bending stress. Remember that a standard SE cylinder relies on live air pressure to hold its load; if pneumatic loss occurs, the piston will drift. For fail-safe load holding, consider the BSE rod lock variant. To retrofit an existing machine, match the 63 mm bore, 15 mm stroke, PT3/8 port, and -S magnet requirement.
AirtacDistr lists every SE63 order code with its price on one page at https://airtacdistr.com/products/airtac-se63-iso-air-cylinder
Quick checklist
At 0.5 MPa, this 63 mm bore cylinder provides 1559 N push and 1402 N pull. At 0.7 MPa, the push force is 2182 N. The maximum push force is 318 kgf at 1.0 MPa.
Yes, the SE63X15S is dimensionally interchangeable with any standard ISO 15552 profile cylinder. You can swap it directly using the existing mounting hardware and PT3/8 ports, provided you pair it with CMSE or DMSE sensors for the magnet.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.