
The AirTAC SE63 Standard Cylinder SE63X1600S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø63mm bore and 1600mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE63X1600S is a double-acting, single-rod ISO 15552 profile cylinder engineered for long-stroke automation. At 0.5 MPa, it generates 1559 N of push force and 1402 N of pull force, scaling to a maximum of 318 kgf at 1.0 MPa. Because this unit features a built-in magnet (S code), it directly supports AirTAC CMSE reed and DMSE electronic position sensing for precise mid-stroke confirmation.
The extruded aluminum barrel omits external tie rods, yielding a compact, corrosion-resistant body that mounts flush in tight spaces. Field-adjustable pneumatic cushioning at both ends allows you to tune end-of-stroke deceleration, softening hard impacts even at higher cycling speeds. Note that the 1600 mm stroke exceeds the 1500 mm standard maximum, making this a made-to-order configuration.
| Model | Airtac SE63 Standard Cylinder SE63X1600S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø63 mm |
| Stroke | 1600 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 1559 N | 1402 N |
| 0.7 MPa | 2182 N | — |
| Max (@1.0 MPa) | 318 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 63 | Bore size in mm. |
| ×1600 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Uses the 1600 mm stroke to push heavy pallets between adjacent conveyor belts, relying on 1559 N of push force to overcome friction.
Maintains tension across wide material webs in a paper mill, using the CMSE magnet to confirm full extension.
Indexes raw steel bar stock into a chuck, utilizing the 63 mm bore's 318 kgf max force to drive long material through the spindle.
This 63 mm bore provides 1559 N push at 0.5 MPa. If your application requires less force, the 50 mm bore offers 982 N push, whereas stepping up to the 80 mm bore yields 2513 N push for heavier loads. Keep in mind that a standard SE cylinder cannot hold a load if air pressure drops or the valve centers; the piston will drift, so an external guide or pilot-operated check valve is required for position holding.
With a 1600 mm stroke, the 20 mm rod and front bearing face significant bending moments under any side load. You must support this long extension with an external linear guide to prevent rod damage and premature seal wear. The PT3/8 port and M16x1.5 rod thread are standardized per ISO 15552, ensuring seamless hardware interchangeability.
AirtacDistr lists every SE63 order code with its price on one page at https://airtacdistr.com/products/airtac-se63-iso-air-cylinder
Quick checklist
This 63 mm bore cylinder delivers 1559 N push and 1402 N pull at 0.5 MPa, 2182 N push at 0.7 MPa, and a maximum of 318 kgf at 1.0 MPa. The 1600 mm stroke exceeds the 1500 mm standard maximum, making it a non-standard, made-to-order unit.
Yes, its mounting dimensions are fully interchangeable with other ISO 15552 profile cylinders. However, the adjustable air cushion only decelerates the piston near the end of stroke; it does not lock or hold the load. If air is lost, the piston will drift unless you add an external rod lock.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.