
The AirTAC SE63 Standard Cylinder SE63X1800S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø63mm bore and 1800mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE63X1800S is a double-acting single-rod ISO 15552 profile cylinder engineered for exceptionally long reach. It delivers a robust 1559 N push at 0.5 MPa, utilizing a 63 mm bore and a built-in magnetic piston for non-contact position detection.
Its square extruded aluminum barrel eliminates external tie rods, providing a flush, corrosion-resistant body that simplifies mounting. Because the 1800 mm stroke exceeds the 1500 mm standard, this unit is configured as a made-to-order assembly, complete with field-adjustable air cushioning at both ends to precisely tune end-of-stroke deceleration.
| Model | Airtac SE63 Standard Cylinder SE63X1800S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø63 mm |
| Stroke | 1800 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 1559 N | 1402 N |
| 0.7 MPa | 2182 N | — |
| Max (@1.0 MPa) | 318 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 63 | Bore size in mm. |
| ×1800 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Pushes heavy loaded pallets across a 1.8-meter transfer station, utilizing the 1559 N extend force to overcome initial rolling friction without hesitation.
Raises and lowers heavy textile warp beams in a weaving mill, where the 1402 N retract force safely pulls the 1800 mm rod back to the home position.
Acts as a diverter arm in a high-speed logistics hub, using the long stroke to span multiple conveyor lanes and push cartons to adjacent sorting chutes.
This 63 mm bore provides 1559 N push at 0.5 MPa. If your application requires less force, stepping down to the 50 mm bore yields 982 N push, while moving up to the 80 mm bore provides 2513 N push. The PT3/8 port and M16x1.5 rod thread accommodate robust pneumatic flow and high side-load capacity.
Because the 1800 mm stroke is non-standard and made-to-order, expect extended lead times. For a stroke of this length, the unsupported piston rod is highly susceptible to bending and sagging; an external guide rail is strongly recommended to prevent premature rod-bearing wear. Note that the adjustable air cushion only decelerates the piston near stroke end and does not lock or hold the load if air pressure is lost. For position holding, consider a BSE rod lock variant.
AirtacDistr lists every SE63 order code with its price on one page at https://airtacdistr.com/products/airtac-se63-iso-air-cylinder
Quick checklist
At 0.5 MPa, the push force is 1559 N and the pull force is 1402 N. At 0.7 MPa, the push force increases to 2182 N. The maximum rated push force is 318 kgf at 1.0 MPa.
Yes, the SE63X1800S is dimensionally interchangeable per ISO 15552 standards. You can use existing ISO 15552 mounting accessories and drop it directly into machinery designed for other ISO 15552 profile cylinders without modifying the footprint.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.