
The AirTAC SE63 Standard Cylinder SE63X180SFTC is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø63mm bore and 180mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE63X180SFTC is a double-acting, single-rod ISO 15552 profile cylinder engineered for rigorous industrial motion. Delivering 1559 N of push force at 0.5 MPa and 1402 N of pull force, it is built around a square extruded aluminum barrel. This design eliminates external tie rods entirely, resulting in a highly compact, corrosion-resistant body that mounts flush against machine frames while keeping the standardized ISO 15552 footprint.
This specific configuration includes an FTC center trunnion mounting accessory and a built-in S magnet for position sensing. The magnet seamlessly interfaces with AirTAC CMSE reed switches and DMSE electronic sensors to provide precise end-of-stroke verification. Furthermore, the cylinder features field-adjustable air cushioning at both ends, allowing technicians to dial in the exact deceleration needed to soften hard end stops at high cycling speeds.
| Model | Airtac SE63 Standard Cylinder SE63X180SFTC |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø63 mm |
| Stroke | 180 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 1559 N | 1402 N |
| 0.7 MPa | 2182 N | — |
| Max (@1.0 MPa) | 318 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 63 | Bore size in mm. |
| ×180 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Provides the 1559 N push force required to cleanly fold heavy corrugated cardboard flaps at high cycle rates on automated packaging lines without stalling.
Utilizes the FTC trunnion mount for smooth pivoting action to deflect finished metal parts down the correct gravity chute, with the S magnet confirming diversion status.
Acts as a robust pneumatic stop gate on a 50 mm conveyor profile, raising a 20 mm rod barrier to halt advancing pallets before an assembly workstation.
When sizing this 63 mm bore actuator, evaluate your force requirements carefully. If 1559 N of push at 0.5 MPa is excessive for your payload, stepping down to the 50 mm bore variant yields 982 N of push, conserving valuable compressed air. Conversely, if your application demands more authority, the 80 mm bore offers 2513 N of push at 0.5 MPa.
Because this model carries an 180 mm stroke, the 20 mm diameter piston rod and M16x1.5 thread experience increased leverage forces during extension. For optimal longevity and to prevent rod-bearing bending, incorporating an external guide alongside the FTC trunnion mount is strongly recommended for unsupported loads. Note that while the adjustable cushions decelerate the piston near the stroke ends, this standard SE cylinder does not hold the load if air pressure is lost; a BSE rod lock variant is required for true position holding.
AirtacDistr lists every SE63 order code with its price on one page at https://airtacdistr.com/products/airtac-se63-iso-air-cylinder
Quick checklist
This 63 mm bore cylinder utilizes a PT3/8 port and a 20 mm hard-chrome rod with an M16x1.5 thread. At 0.5 MPa it generates 1559 N of push force and 1402 N of pull force. At 0.7 MPa the push increases to 2182 N, with an absolute maximum push capacity of 318 kgf at 1.0 MPa.
Yes, the SE63X180SFTC is dimensionally interchangeable per ISO 15552 standards. You can drop it directly into existing mounting footprints and use shared ISO 15552 hardware, provided your machine accommodates the FTC trunnion accessory and PT3/8 porting.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.