verified AirTAC China Authorized Export Seller shield 100% Genuine AirTAC Parts workspace_premium 1-Year Warranty
appsShop by Modelexpand_more
person shopping_cart Request a QuoteQuote
AirTAC SE Series · ISO 15552 Cylinder

Airtac SE63 Standard Cylinder SE63X193SN

The AirTAC SE63 Standard Cylinder SE63X193SN is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø63mm bore and 193mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.

  • BoreØ63 mm
  • Stroke193 mm
  • Port sizePT3/8
  • Acting typeDouble acting
  • Rod threadM16×1.5
  • CushionAdjustable, 36 mm
$103.25 $110.75Save 6% Standard model — usually dispatched in 3-5 days
Request a Quote
  • No minimum order. A single piece can be ordered.
  • Shipped from our own warehouse: most standard models dispatch in 3–5 days; custom and non-standard models take 8–10 business days. Transit time after that depends on the destination.
Compare every SE63 stroke, mounting and version on one page All SE63 codes →
verified Genuine AirTAC workspace_premium 1-year warranty bolt Reply in 7 h

About the Airtac SE63 Standard Cylinder SE63X193SN

The AirTAC SE63X193SN is a double-acting, single-rod ISO 15552 profile cylinder engineered for demanding pneumatic tasks. It features a 63 mm bore and a 193 mm stroke, yielding a robust 1559 N push force at 0.5 MPa and a maximum output of 318 kgf at 1.0 MPa. The extruded aluminum barrel design omits external tie rods, presenting a clean, corrosion-resistant exterior that mounts flush against machine frames while protecting internal mechanics.

This specific configuration incorporates an NBR seal for reliable operation across standard temperature ranges and a built-in magnet (-S) for seamless integration with AirTAC CMSE reed and DMSE electronic position sensors. The square body integrates sensor grooves on three sides, allowing flexible switch placement. Furthermore, the field-adjustable pneumatic cushioning at both ends lets technicians dial in end-of-stroke deceleration via a set screw, effectively neutralizing hard mechanical shocks during high-speed cycling.

Airtac SE63 Standard Cylinder SE63X193SN Technical Specifications

ModelAirtac SE63 Standard Cylinder SE63X193SN
SeriesSE ISO 15552 profile cylinder
Bore sizeØ63 mm
Stroke193 mm
Acting typeDouble acting
Port sizePT3/8
Rod threadM16×1.5
FluidAir (filtered by 40µm element)
Operating pressure0.15 – 1.0 MPa
Proof pressure1.5 MPa
Temperature-20 to +70 °C (0–150 °C with FKM seals)
Speed range30 – 800 mm/s
CushionAdjustable, 36 mm
Max strokeUp to 1500 mm

Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).

Theoretical Output Force (Ø63mm)

PressurePush forcePull force
0.5 MPa1559 N1402 N
0.7 MPa2182 N—
Max (@1.0 MPa)318 kgf

Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.

Model Code: Airtac SE63 Standard Cylinder SE63X193SN

SEISO 15552 / VDMA 24562 profile-barrel double-acting cylinder.
63Bore size in mm.
×193Stroke length in mm.
-SOptional built-in magnet for CMSE / DMSE sensor sensing.

Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).

Where the Airtac SE63 Standard Cylinder SE63X193SN Is Used

packaging

Carton Erector Flaps

Drives the folding mechanism on continuous carton erectors, utilizing the 1559 N push force to cleanly crease heavy corrugated cardboard flaps at high cycle rates without stalling.

conveyor_belt

Belt Tensioner Arm

Applies constant dynamic tension to long package conveyor belts, where the 193 mm stroke accommodates belt stretch and the NBR seal resists ambient warehouse dust and moisture.

straighten

Metal Press Ejector

Ejects stamped metal brackets from a hydraulic press bed, leveraging the adjustable end-cushions to softly decelerate the 20 mm rod before it strikes the press frame at full extension.

Is the Airtac SE63 Standard Cylinder SE63X193SN the Right Cylinder?

Selecting the SE63X193SN is optimal when your application requires the 1559 N push force at 0.5 MPa. If your load demands less energy, stepping down to the 50 mm bore yields 982 N of push force, whereas scaling up to the 80 mm bore provides 2513 N. Because this is a double-acting cylinder, it relies on continuous air pressure to move and hold the load; if the air supply is lost or the directional valve is centered, the piston will drift. For position-holding safety, consider the BSE rod-lock variant. Furthermore, the 193 mm stroke combined with the 20 mm rod is well-suited for the PT3/8 port flow, but at this length, you must account for rod-bearing bending under heavy lateral loads and utilize an external guide rail to prevent premature wear.

For retrofitting, this cylinder is dimensionally interchangeable with any standard ISO 15552 profile cylinder, meaning it drops directly into existing footprints without requiring custom mounting brackets. It uses a PT3/8 port and a standard M16x1.5 rod-end thread, ensuring straightforward plumbing and mechanical linkage integration.

AirtacDistr lists every SE63 order code with its price on one page at https://airtacdistr.com/products/airtac-se63-iso-air-cylinder

Quick checklist

  • ✓ Required force at your working pressure
  • ✓ Stroke and mounting space
  • ✓ Port/thread type (PT/G)
  • ✓ Magnet (-S) for CMSE/DMSE sensors?
  • ✓ Side load — consider a guided cylinder
Ask an Engineer

Installation & Maintenance Notes

  • check Use clean air filtered to 40µm or finer.
  • check Keep within 0.15 – 1.0 MPa operating pressure.
  • check Avoid side load on the piston rod.
  • check Adjust end cushion screws for smooth stops.
  • check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
  • check Installation by qualified personnel per AirTAC docs.

Airtac SE63 Standard Cylinder SE63X193SN FAQ

This 63 mm bore cylinder delivers a push force of 1559 N and a pull force of 1402 N at 0.5 MPa. At 0.7 MPa, the push force is 2182 N, with a maximum push capacity of 318 kgf at 1.0 MPa. It operates at pressures from 0.15-1.0 MPa and speeds of 30-800 mm/s.

No, the SE63X193SN is a standard double-acting cylinder and will drift if air pressure is lost or the valve is centered. The adjustable air cushion at both ends only decelerates the piston near the stroke end; it does not lock or hold the load. For fail-safe position holding, an AirTAC BSE series rod lock cylinder is required.

verified

Authorized Export Seller

Genuine AirTAC parts produced by AirTAC factory.

workspace_premium

1-Year Warranty

Covers non-human-caused product damage.

local_shipping

Fast Dispatch

Most standard models are dispatched in 3-5 days.

bolt

Fast Reply

Most inquiries answered within 7 hours.

Related AirTAC SE Cylinders

Request a Quote for Airtac SE63 Standard Cylinder SE63X193SN

Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.

Thank you. We received your request for SE63X193SN and will confirm price, availability and lead time — usually within 7 hours.

For the fastest response, keep the complete model number above and include a clear photo of the product label. If photo upload is unavailable, email photos to [email protected] with your model number.