
The AirTAC SE63 Standard Cylinder SE63X200N is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø63mm bore and 200mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE63X200N is a double-acting, single-rod ISO 15552 profile cylinder engineered for a 63 mm bore and 200 mm stroke. It delivers a robust 1559 N of push force at 0.5 MPa, utilizing a PT3/8 port and a 20 mm hard-chrome piston rod. This specific SKU relies on an NBR seal, making it highly suitable for standard pneumatic operations rather than the high-temperature environments that demand FKM elastomers.
Built with an extruded aluminum barrel that eliminates external tie rods, the body is inherently compact and resistant to corrosion while allowing accessories to mount flush against the profile. The cylinder features field-adjustable pneumatic cushioning at both ends, enabling technicians to fine-tune end-of-stroke deceleration via a set screw to prevent hard mechanical impacts. Note that this particular unit lacks a built-in magnet, so it cannot directly host CMSE or DMSE position sensors without modification.
| Model | Airtac SE63 Standard Cylinder SE63X200N |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø63 mm |
| Stroke | 200 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 1559 N | 1402 N |
| 0.7 MPa | 2182 N | — |
| Max (@1.0 MPa) | 318 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 63 | Bore size in mm. |
| ×200 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Actuates a routing flap on a high-speed logistics conveyor, utilizing the 1559 N push force at 0.5 MPa to reliably deflect heavy cardboard cartons without stalling.
Pushes raw metal stock into a turning center spindle, where the 200 mm stroke and adjustable end-cushions prevent impact damage to the lathe chuck during rapid retraction.
Drives an auxiliary ejection pin for a plastic molding machine, relying on the NBR seal for consistent cycling in standard 70°C shop environments.
When sizing this 63 mm bore cylinder, evaluate your force margins: the SE50X200 provides 982 N of push at 0.5 MPa, while stepping up to the SE80X200 yields 2513 N. If your mechanism must hold a load vertically or resist drifting when air pressure is lost, remember that a standard SE cylinder will drift; you would need to integrate a BSE rod lock or an external pilot-operated check valve for secure positioning. Because this 200 mm stroke is below the 300 mm threshold, side-load stress on the rod bearing is minimal, though heavy offset loads still require external guiding.
For ISO 15552 retrofits, this cylinder serves as a dimensionally interchangeable direct replacement. To match this exact configuration, specify the 63 mm bore, 200 mm stroke, PT3/8 port thread, NBR seal, and your desired mounting accessory (such as FA front flange or TC centre trunnion). Since this SKU omits the -S magnet, confirm if your control system requires external limit switches or a different variant with an embedded magnet.
AirtacDistr lists every SE63 order code with its price on one page at https://airtacdistr.com/products/airtac-se63-iso-air-cylinder
Quick checklist
At 0.5 MPa, the SE63X200N provides 1559 N of push force and 1402 N of pull force. At 0.7 MPa, the push force increases to 2182 N, with a maximum push capacity of 318 kgf at 1.0 MPa. The operating speed ranges from 30 to 800 mm/s.
Yes, it is dimensionally interchangeable with other ISO 15552 profile cylinders and shares standard mounting interfaces. However, because this specific SE63X200N SKU lacks the built-in -S magnet, it cannot directly support AirTAC CMSE or DMSE position sensors without upgrading to a magnet-equipped variant.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.