
The AirTAC SE63 Standard Cylinder SE63X250SFTC is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø63mm bore and 250mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE63X250SFTC is a double-acting single-rod profile cylinder delivering a robust 1559 N push at 0.5 MPa. Built to the ISO 15552 standard, its extruded aluminum barrel lacks external tie rods, yielding a compact footprint that mounts flush against machine frames while resisting corrosion. The FTC center-trunnion accessory provides a pivoting anchor point ideal for mid-stroke arc movements.
Equipped with a built-in position magnet, this unit interfaces directly with AirTAC CMSE reed and DMSE electronic sensors for precise end-of-stroke detection. The field-adjustable air cushioning at both ends allows technicians to tune the deceleration of the 250 mm stroke via a set screw, softening hard mechanical impacts without relying on fixed rubber bumpers.
| Model | Airtac SE63 Standard Cylinder SE63X250SFTC |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø63 mm |
| Stroke | 250 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 1559 N | 1402 N |
| 0.7 MPa | 2182 N | — |
| Max (@1.0 MPa) | 318 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 63 | Bore size in mm. |
| ×250 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Leverages the 1559 N push force and FTC trunnion mount to pivot guide rails, smoothly rerouting glass containers between filling lanes at high cycle rates.
Uses the precise 250 mm stroke and DMSE electronic sensor feedback to time the folding of heavy cardboard flaps just before the sealing head applies tape.
Employs the 1402 N pull force to retract and secure machining pallets, relying on the adjustable end cushions to soften the stop and protect the fixture alignment.
This 63 mm bore generates 1559 N push at 0.5 MPa. If your application requires less force, the 50 mm bore offers 982 N push; if you need substantially more power, stepping up to the 80 mm bore yields 2513 N push. Because the 250 mm stroke creates extended leverage, external guide rails should support the load to prevent rod-bearing bending and premature seal wear. As a true ISO 15552 cylinder, it serves as a direct dimensional replacement for competing profile cylinders, utilizing the same PT3/8 port and M16x1.5 rod thread.
AirtacDistr lists every SE63 order code with its price on one page at https://airtacdistr.com/products/airtac-se63-iso-air-cylinder
Quick checklist
At 0.5 MPa, this 63 mm bore cylinder provides 1559 N of push force and 1402 N of pull force. At 0.7 MPa, the push force increases to 2182 N, with a maximum push capacity of 318 kgf at 1.0 MPa. The operational speed range is 30-800 mm/s.
No, the adjustable air cushion only decelerates the piston near the stroke ends and does not act as a braking mechanism. If air pressure drops, the piston will drift. For position holding under load, an external pilot-operated check valve or a dedicated BSE rod lock variant is required.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.