
The AirTAC SE63 Standard Cylinder SE63X270S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø63mm bore and 270mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE63X270S is a double-acting, single-rod ISO 15552 profile cylinder engineered to deliver 1559 N of push force at 0.5 MPa. Its square extruded aluminum barrel eliminates external tie rods, yielding a compact, corrosion-resistant body that mounts flush against machine frames while exposing standardized interface dimensions for universal hardware compatibility.
Equipped with a built-in magnet (-S), this unit supports AirTAC CMSE reed and DMSE electronic sensors for precise end-of-stroke detection. Field-adjustable pneumatic cushioning at both ends allows you to tune deceleration and soften hard mechanical stops during high-speed 30-800 mm/s cycles.
| Model | Airtac SE63 Standard Cylinder SE63X270S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø63 mm |
| Stroke | 270 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 1559 N | 1402 N |
| 0.7 MPa | 2182 N | — |
| Max (@1.0 MPa) | 318 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 63 | Bore size in mm. |
| ×270 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Provides the 1559 N push and 270 mm travel required to fold and seal corrugated carton blanks at high cycle rates.
Executes 270 mm strokes to push heavy pallets across transfer lines, relying on adjustable cushions to soften end stops.
Manages the robust 270 mm reach and 318 kgf max output needed to open and close heavy safety guards on molding machinery.
Stepping down to the 50 mm bore reduces the 0.5 MPa push to 982 N, whereas moving up to the 80 mm bore increases it to 2513 N. At 270 mm of stroke, the 20 mm rod and M16x1.5 thread handle substantial loads, but long unsupported strokes invite rod-bearing bending; an external guide is recommended to prevent side-load damage. Remember that the adjustable air cushion only decelerates the piston near stroke end—it is not a rod lock, so loads will drift if air pressure is lost. As a dimensionally interchangeable ISO 15552 cylinder, it serves as a direct replacement sharing the PT3/8 port and standard mounting accessories.
AirtacDistr lists every SE63 order code with its price on one page at https://airtacdistr.com/products/airtac-se63-iso-air-cylinder
Quick checklist
At 0.5 MPa, the SE63X270S delivers 1559 N of push force and 1402 N of pull force. At 0.7 MPa, the push force reaches 2182 N, with a maximum push capacity of 318 kgf at 1.0 MPa. The operating speed range is 30-800 mm/s.
Yes, the SE63X270S is dimensionally interchangeable per ISO 15552 standards, meaning it shares the exact mounting footprint, 63 mm bore, 270 mm stroke, and PT3/8 port of other profile cylinders. You can drop it into existing ISO 15552 hardware without machining.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.