
The AirTAC SE63 Standard Cylinder SE63X300SN is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø63mm bore and 300mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE63X300SN is a double-acting single-rod ISO 15552 profile cylinder engineered for demanding pneumatic tasks. Operating at 0.5 MPa, it generates 1559 N of push force and 1402 N of pull force, making it a robust choice for mid-weight industrial actuation. The extruded aluminum barrel design omits external tie rods, yielding a compact, corrosion-resistant profile that mounts flush against machine frames while protecting internal components.
This 63mm bore unit features a built-in magnet (-S) compatible with AirTAC CMSE reed and DMSE electronic sensors for precise end-of-stroke detection. Equipped with NBR seals, it is tailored for standard temperature environments. The field-adjustable air cushioning at both ends allows technicians to fine-tune end-of-stroke deceleration via a set screw, softening hard mechanical stops during high-speed operations.
| Model | Airtac SE63 Standard Cylinder SE63X300SN |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø63 mm |
| Stroke | 300 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 1559 N | 1402 N |
| 0.7 MPa | 2182 N | — |
| Max (@1.0 MPa) | 318 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 63 | Bore size in mm. |
| ×300 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Delivers 1559 N of push force across the 300mm stroke to reliably fold and seal heavy corrugated carton flaps on high-speed packaging lines.
Uses the integrated magnet with DMSE sensors to confirm full extension of a 300mm stroke routing gate, smoothly diverting heavy pallets between conveyor tracks.
Provides robust 1402 N retraction force to safely extract plastic blow-molded jerry cans from hot tooling, utilizing the adjustable cushion to soften the return impact.
Generating 1559 N push at 0.5 MPa, this model sits perfectly between the 50mm bore (982 N push) and the 80mm bore (2513 N push), allowing you to scale up or down depending on your exact load requirements. Because this is a double-acting cylinder, it relies on continuous air pressure to move and hold the piston; it will drift if air is lost or the valve is centered, so an external rod lock or pilot-operated check valve is required for fail-safe load holding.
At 300mm of stroke, the 20mm rod and thread experience increased bending moments under side loads, so an external guide rail is strongly recommended to prevent premature rod-bearing wear. For direct retrofits, this cylinder is dimensionally interchangeable with any true ISO 15552 profile cylinder, sharing identical mounting footprint hardware, a PT3/8 port, and standard sensor grooves.
AirtacDistr lists every SE63 order code with its price on one page at https://airtacdistr.com/products/airtac-se63-iso-air-cylinder
Quick checklist
At 0.5 MPa, the SE63X300SN delivers 1559 N of push force and 1402 N of pull force. At 0.7 MPa, the push force increases to 2182 N, with a maximum push capacity of 318 kgf at 1.0 MPa. The operational speed range is 30-800 mm/s.
Yes, it is dimensionally interchangeable per ISO 15552 standards, sharing the exact same mounting interface and PT3/8 port sizes. The field-adjustable air cushion at both ends allows you to manually tune the end-of-stroke deceleration via a screw, which softens impacts but does not lock or hold the load without air pressure.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.