verified AirTAC China Authorized Export Seller shield 100% Genuine AirTAC Parts workspace_premium 1-Year Warranty
appsShop by Modelexpand_more
person shopping_cart Request a QuoteQuote
AirTAC SE Series · ISO 15552 Cylinder

Airtac SE63 Standard Cylinder SE63X318S

The AirTAC SE63 Standard Cylinder SE63X318S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø63mm bore and 318mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.

  • BoreØ63 mm
  • Stroke318 mm
  • Port sizePT3/8
  • Acting typeDouble acting
  • Rod threadM16×1.5
  • CushionAdjustable, 36 mm
$124.66 $132.16Save 5% Standard model — usually dispatched in 3-5 days
Request a Quote
  • No minimum order. A single piece can be ordered.
  • Shipped from our own warehouse: most standard models dispatch in 3–5 days; custom and non-standard models take 8–10 business days. Transit time after that depends on the destination.
Compare every SE63 stroke, mounting and version on one page All SE63 codes →
verified Genuine AirTAC workspace_premium 1-year warranty bolt Reply in 7 h

About the Airtac SE63 Standard Cylinder SE63X318S

The AirTAC SE63X318S is a double-acting, single-rod ISO 15552 profile cylinder engineered to deliver a robust 1559 N push force at 0.5 MPa. Its square extruded aluminum barrel completely eliminates external tie rods, yielding a highly compact, corrosion-resistant body that mounts flush against machine frames while preventing debris buildup. Because this is a 318 mm stroke configuration, it is produced as a non-standard, made-to-order length to suit specialized actuation distances.

Equipped with a built-in magnet (-S), this unit seamlessly integrates with AirTAC CMSE reed and DMSE electronic sensors for precise end-of-stroke detection. The field-adjustable pneumatic air cushioning at both ends allows technicians to tune end-cap deceleration via a set screw, softening hard mechanical stops during high-speed 30-800 mm/s cycles.

Airtac SE63 Standard Cylinder SE63X318S Technical Specifications

ModelAirtac SE63 Standard Cylinder SE63X318S
SeriesSE ISO 15552 profile cylinder
Bore sizeØ63 mm
Stroke318 mm
Acting typeDouble acting
Port sizePT3/8
Rod threadM16×1.5
FluidAir (filtered by 40µm element)
Operating pressure0.15 – 1.0 MPa
Proof pressure1.5 MPa
Temperature-20 to +70 °C (0–150 °C with FKM seals)
Speed range30 – 800 mm/s
CushionAdjustable, 36 mm
Max strokeUp to 1500 mm

Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).

Theoretical Output Force (Ø63mm)

PressurePush forcePull force
0.5 MPa1559 N1402 N
0.7 MPa2182 N—
Max (@1.0 MPa)318 kgf

Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.

Model Code: Airtac SE63 Standard Cylinder SE63X318S

SEISO 15552 / VDMA 24562 profile-barrel double-acting cylinder.
63Bore size in mm.
×318Stroke length in mm.
-SOptional built-in magnet for CMSE / DMSE sensor sensing.

Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).

Where the Airtac SE63 Standard Cylinder SE63X318S Is Used

package_2

Carton Erector Flap Folding

Drives the folding mechanism on continuous-motion packaging lines, utilizing the 1559 N push force and 318 mm stroke to cleanly tuck and seal corrugated carton flaps at high cycling speeds.

factory

CNC Lathe Bar Feeder

Pushes raw bar stock through the spindle collet, where the 318 mm extension and integrated DMSE sensor ensure accurate material positioning without over-traveling the chuck.

straighten

Automotive Press Ejection

Ejects stamped metal panels from forming dies, relying on the 1402 N retract force to safely withdraw the 20 mm rod and clear the mold cavity before the upper tooling descends.

Is the Airtac SE63 Standard Cylinder SE63X318S the Right Cylinder?

When sizing this actuator, note that the 318 mm stroke exceeds the 1500 mm standard maximum for the 63 mm bore, classifying it as a non-standard made-to-order stroke. To scale your output, stepping down to the 50 mm bore yields 982 N of push at 0.5 MPa, while stepping up to the 80 mm bore provides 2513 N. Because the stroke exceeds 300 mm, the 20 mm rod and internal bearing face increased bending moments under side loads; always support the tooling with an external linear guide to prevent premature wear. Remember that the adjustable cushion only decelerates the piston near stroke end and cannot hold a load if air pressure drops—use a BSE rod lock for static holding. As a true ISO 15552 profile cylinder, it offers a direct replacement footprint for any standard VDMA 24562 mounting accessory utilizing its PT3/8 port and M16x1.5 rod thread.

AirtacDistr lists every SE63 order code with its price on one page at https://airtacdistr.com/products/airtac-se63-iso-air-cylinder

Quick checklist

  • ✓ Required force at your working pressure
  • ✓ Stroke and mounting space
  • ✓ Port/thread type (PT/G)
  • ✓ Magnet (-S) for CMSE/DMSE sensors?
  • ✓ Side load — consider a guided cylinder
Ask an Engineer

Installation & Maintenance Notes

  • check Use clean air filtered to 40µm or finer.
  • check Keep within 0.15 – 1.0 MPa operating pressure.
  • check Avoid side load on the piston rod.
  • check Adjust end cushion screws for smooth stops.
  • check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
  • check Installation by qualified personnel per AirTAC docs.

Airtac SE63 Standard Cylinder SE63X318S FAQ

The SE63X318S generates 1559 N of push force and 1402 N of pull force at 0.5 MPa. At 0.7 MPa, the push force is 2182 N, with an absolute maximum push of 318 kgf at 1.0 MPa. It features a PT3/8 port and a 20 mm piston rod.

Yes, the SE63X318S is dimensionally interchangeable per ISO 15552 / VDMA 24562 standards. You can use it as a direct replacement for other ISO 15552 profile cylinders, retaining your existing mounting hardware and sensor brackets.

verified

Authorized Export Seller

Genuine AirTAC parts produced by AirTAC factory.

workspace_premium

1-Year Warranty

Covers non-human-caused product damage.

local_shipping

Fast Dispatch

Most standard models are dispatched in 3-5 days.

bolt

Fast Reply

Most inquiries answered within 7 hours.

Related AirTAC SE Cylinders

Request a Quote for Airtac SE63 Standard Cylinder SE63X318S

Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.

Thank you. We received your request for SE63X318S and will confirm price, availability and lead time — usually within 7 hours.

For the fastest response, keep the complete model number above and include a clear photo of the product label. If photo upload is unavailable, email photos to [email protected] with your model number.