
The AirTAC SE63 Standard Cylinder SE63X400SN is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø63mm bore and 400mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE63X400SN is a double-acting single-rod ISO 15552 profile cylinder delivering a substantial 1559 N push force at 0.5 MPa. Driven by a PT3/8 port, it features a Ø20 mm medium-carbon steel rod and an M16x1.5 thread. The square extruded aluminum barrel eliminates external tie rods, yielding a compact, corrosion-resistant body that mounts flush on machinery while retaining the standardized ISO 15552 footprint for direct retrofitting.
Equipped with a built-in magnet (-S), this unit seamlessly integrates AirTAC CMSE reed and DMSE electronic sensors for precise end-of-stroke detection. The NBR seal provides reliable operation within the standard -20 to +70 C temperature range. Field-adjustable pneumatic cushioning at both ends allows you to tune deceleration via a screw, softening hard end stops during high-speed 400 mm strokes.
| Model | Airtac SE63 Standard Cylinder SE63X400SN |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø63 mm |
| Stroke | 400 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 1559 N | 1402 N |
| 0.7 MPa | 2182 N | — |
| Max (@1.0 MPa) | 318 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 63 | Bore size in mm. |
| ×400 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Uses the 400 mm stroke to push heavy pallets sideways onto secondary processing lanes, relying on the 1559 N push force to overcome friction without hesitation.
Drives the folding mechanism on continuous packaging lines, where the NBR seal endures millions of cycles and the -S magnet triggers DMSE sensors to confirm flap closure.
Ejects stamped metal brackets from a hydraulic press, utilizing the field-adjustable air cushions to gently decelerate the 2182 N push force at 0.7 MPa before end impact.
Selecting the SE63X400SN means sizing for a 1559 N push at 0.5 MPa. If your application requires less force, stepping down to the 50 mm bore yields 982 N push. If you need more power, stepping up to the 80 mm bore provides 2513 N push. Because this is a 400 mm stroke, the unsupported piston rod is highly susceptible to side-load bending; always pair it with an external guide to prevent premature rod-bearing wear.
For exact ISO 15552 direct replacement, match the 63 mm bore, 400 mm stroke, PT3/8 port, and your required mounting accessory. Remember that a plain SE cylinder will drift and lose its load position if air pressure drops or the valve centers; the adjustable cushion only decelerates the piston near stroke end and does not act as a brake. For positive holding, consider the BSE rod lock variant.
AirtacDistr lists every SE63 order code with its price on one page at https://airtacdistr.com/products/airtac-se63-iso-air-cylinder
Quick checklist
The SE63X400SN features a PT3/8 port and generates 1559 N push and 1402 N pull at 0.5 MPa. At 0.7 MPa, the push force is 2182 N. The maximum allowable push force is 318 kgf at 1.0 MPa.
No, the standard SE cylinder does not hold position without live air pressure. The built-in adjustable air cushion only decelerates the piston near the end of the stroke; it is not a locking mechanism. For positive load holding, use the BSE rod lock variant or an external pilot-operated check valve.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.