
The AirTAC SE63 Standard Cylinder SE63X420SH is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø63mm bore and 420mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE63X420SH is a double-acting, single-rod ISO 15552 profile cylinder engineered for demanding environments. It delivers 1559 N of push force and 1402 N of pull force at 0.5 MPa, utilizing a 63 mm bore and a 420 mm stroke. Equipped from the factory with FKM (Viton) seals, this unit reliably operates in ambient temperatures up to 150 C, making it highly suitable for thermal processing equipment where standard elastomers would quickly degrade.
Unlike traditional tie-rod designs, the SE series relies on a square extruded aluminum barrel that lacks external protruding rods. This clean profile not only resists corrosion but also allows for flush mounting on tight machine frames. Furthermore, the built-in magnet (-S) directly supports AirTAC CMSE reed and DMSE electronic sensors, which seat neatly into the three-sided sensor grooves to provide precise end-of-stroke detection without requiring bulky external brackets.
| Model | Airtac SE63 Standard Cylinder SE63X420SH |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø63 mm |
| Stroke | 420 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 1559 N | 1402 N |
| 0.7 MPa | 2182 N | — |
| Max (@1.0 MPa) | 318 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 63 | Bore size in mm. |
| ×420 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Provides 1559 N of push at 0.5 MPa to safely strip hot plastic parts from mold cavities, with FKM seals surviving ambient press heat up to 150 C.
Delivers 1402 N of retract force at 0.5 MPa to pull a forming die back to home position, utilizing the 420 mm stroke for deep-draw operations.
Pushes heavy baskets through a tempering oven entrance, where the FKM Viton seals resist thermal degradation and the square barrel mounts flush to the oven frame.
When sizing this 63 mm bore cylinder, evaluate your load dynamics carefully. If you require less force, stepping down to the 50 mm bore yields 982 N of push at 0.5 MPa, whereas stepping up to the 80 mm bore provides 2513 N. Because this unit features a 420 mm stroke, the extended 20 mm rod is subjected to greater bending moments under side loads; always incorporate an external guide rail to prevent premature rod-bearing wear.
As a true ISO 15552 profile cylinder, the SE63X420SH offers a dimensionally interchangeable footprint, serving as a direct replacement for other ISO 15552 cylinders while utilizing standard mounting hardware and a PT3/8 port. Remember that this is a double-acting air cylinder: if air pressure is lost or the directional valve is centered, the piston will drift and cannot hold a load. For fail-safe position holding, consider the AirTAC BSE rod-lock variant.
AirtacDistr lists every SE63 order code with its price on one page at https://airtacdistr.com/products/airtac-se63-iso-air-cylinder
Quick checklist
This 63 mm bore cylinder generates 1559 N of push force and 1402 N of pull force at 0.5 MPa. At 0.7 MPa, the push force increases to 2182 N, with a maximum push capacity of 318 kgf at 1.0 MPa. The operational speed ranges from 30-800 mm/s.
Yes, it is dimensionally interchangeable with any standard ISO 15552 profile cylinder, sharing standard mounting dimensions and a PT3/8 port. It features field-adjustable air cushions at both ends that decelerate the piston near the stroke limits; you can tune the needle valves to soften hard end-stops at high speeds.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.