
The AirTAC SE63 Standard Cylinder SE63X430S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø63mm bore and 430mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE63X430S is a double-acting single-rod ISO 15552 profile cylinder engineered to deliver 1559 N of push force at 0.5 MPa. Its square extruded aluminum barrel omits external tie rods, yielding a compact, corrosion-resistant body that mounts flush against machine frames while exposing standardized ISO 15552 interface dimensions for seamless retrofitting.
Equipped with a built-in magnet (-S), this unit supports AirTAC CMSE reed and DMSE electronic sensors for precise end-position detection. The field-adjustable pneumatic cushioning at both ends allows technicians to tune end-cap deceleration via a set screw, softening hard mechanical stops during high-speed 30-800 mm/s cycling.
| Model | Airtac SE63 Standard Cylinder SE63X430S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø63 mm |
| Stroke | 430 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 1559 N | 1402 N |
| 0.7 MPa | 2182 N | — |
| Max (@1.0 MPa) | 318 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 63 | Bore size in mm. |
| ×430 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Uses the 430 mm stroke to index empty pallets out of a magazine stack, relying on the 1559 N push force to overcome friction without stalling.
Extends to fold and lock corrugated carton flaps, using the adjustable end cushions to prevent tearing the board at high operating speeds.
Pulls automated analyzer sample trays out of a chamber, leveraging the 1402 N retract force and the -S magnet for DMSE electronic position feedback.
Delivering 1559 N push at 0.5 MPa, this 63 mm bore sits perfectly between the 50 mm bore (982 N push) and the 80 mm bore (2513 N push), letting you step down for lighter clamping or up for heavier lifting. Because the 430 mm stroke creates a long unsupported rod span, adding an external guide rail is critical to prevent rod-bearing bending under side loads.
This standard configuration uses a PT3/8 port, a Ø20 mm rod with an M16x1.5 thread, and the -S magnet. Remember that a plain SE cylinder relies on live air pressure to move; if air is lost or the valve centers, the piston drifts and cannot hold a load—specify a BSE rod lock variant if static holding is required.
AirtacDistr lists every SE63 order code with its price on one page at https://airtacdistr.com/products/airtac-se63-iso-air-cylinder
Quick checklist
At 0.5 MPa, the push force is 1559 N and the pull force is 1402 N. At 0.7 MPa, the push force is 2182 N. The maximum allowable push force is 318 kgf at 1.0 MPa.
No, the standard SE cylinder is double-acting and cannot hold a load if air is lost or the valve is centered, as the piston will drift. The adjustable air cushion only decelerates the piston near stroke end; it does not lock the rod. For position holding, consider the BSE rod lock variant.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.